tevo delta dual extruder 3d models

I created this to be able to mount two extruders under the top frame of my delta Printer. It's fitted with two E3D titan extruders but will fit others. Just print one normal position and one mirrored in the your slicer software. ... To mount the...

I created this to be able to mount two extruders under the top frame of my delta Printer.It's fitted with two E3D titan extruders but will fit others. ... Just print one normal position and one mirrored in the your slicer software.

Remix of "Dual Blower/Radial Fan Duct Mount (Tevo Tarantula)" (https://www.thingiverse.com/thing:1850163/#files). All credit goes to designer Supasorn Suwajanakorn (https://www.thingiverse.com/supasorn/about). I couldn't find this exact fan duct...

I would insulate the sides of the fan cover with Kapton tape at least as they are quite close to the hot end and may warp at temperatures above about 240 deg, The mod is based on the Tevo tarantula dual extruder upgrade which can be found here :-...

I would insulate the sides of the fan cover with Kapton tape at least as they are quite close to the hot end and may warp at temperatures above about 240 deg, The mod is based on the Tevo tarantula dual extruder upgrade which can be found here :-...

TEVO TORNADO CR10 dual extruder T[old_tool] G92E0 ; G1 E-3 F3600 ; retract the filament from melting zone G92E0 ; G0 X320 F6000 ;move the hotend to bed edges or corners to finish the filament swap job. normally over the prim pillar is ideal G1 E3...

I designed this to suspend my dual extruders above my hot end. This mount should be placed level with the vertical slides when the nozzle is at 0,0,0. I put hook points on my slides an there are three hook attachment points on the mount. There is a...

WORK IN PROGRESS Fusion 360 users, you can download and edit via this link: Flying extruder: https://a360.co/2VuV3UB Y-Feeder https://a360.co/2vpjm7Q

The fan mount fits on dual hotend coolsink for tevo tarantula and fits two 5015 blower fans on the sides. The differences with the above design are: 1) stiffnes, 2) asimmetric design due to rotated position of right blower to get the air from the...

TEVO Tarantula X Carriage (Dual Extruder).

tevo tarantula dual extruder sensor proximity support z

Delta flying BMG dual drive/titan extruder

Dual Fan Support for TEVO Tarantula Dual Extruder ---------------------------------------------------------------------- This is one of the first upgrades that the TEVO Tarantula needs. Before using fans I had problems with printing quality, but...

This is a standoff for mounting the SN04 Autolevelling sensor on the back of the Tevo Tarantula Dual Extruder heatsink. The existing holes were too high on mine - possibly because they were drilled at the wrong end at the factory. ...Even if they had...

I disigned it for the Tevo Tarantula dual Extruder (default Hotend from Tevo). It fits 2 radial Fans and there can be screw togehter with the Holder (2* M4x25 and 2* M4 Nuts). The Assembly is like a sandwitch. The holder will be assembled...

Requiments: 1x BLTouch -Hotend: 2x Fullmetal CR10 Hotend 2x 100K Glas Thermistor 2x 24V Heating capsule -Extruder: 2x Nema17 Angle 1.8° 2x Creality CR-10 E3D or other Feeder 2x Extruder Drivers -Screw and Nuts: 9x M3 Screw ca. 1.5cm 4x M3 Nuts 4x...

The auto leveling sensor is very hard to access on the Tarantula with dual extruder, as it is hidden behind the extruder. This thing exposes a screw on the hole meant for the sensor cable, turning the screw moves the sensor up and down making the...

Hi Remix of https://www.thingiverse.com/thing:2632046 to give 10mm extra between the two extruders. Thanks to the original author. The original model had them too close to each other for my liking. I also made the model slightly lower to fit...

I designed this to suit my Delta Rostock and Alu Hotends. It is Work in progress. But i have it fully functional on my printer. I will be making some mods in the future. ...Like hotend adjustment and Fan for cooling print.

I designed this to suit my Delta Rostock and Alu Hotends. It is Work in progress. But i have it fully functional on my printer. I will be making some mods in the future. ...Like hotend adjustment and Fan for cooling print.

Modified to fit the Tevo Tarantula stock carriage but should fit any Chimera dual extruder as long as there is clearance for the fans, Tested fit on the single extruder but have not tested a dual extruder yet. ... Designed to fit 50x15mm Blower Fans...

Dual Extruder, Dual Radial Fan Duct. This is the 3rd version of this fan duct. ...The design intention is to provide very powerful cooling effect in a minimal footprint, because I love to watch the TT print.

Just added the 18mm sensor mount to the dual fang radial fan duct for stock tevo tarantula dual extruder setup. Its a little tight for the top sensor nut, but seems to work well. This will put my sensor 47mm right and 30mm forward from the first...

The concept of dual-extruder for the delta printers This thing is a work in progress Do not try to print

This part is designed to be attached to the top side of your x carriage mount on the HE3D Ei3 or Tevo Tarantula with stock dual extruder. This top is thin enough to be mounted with the original screws. The part should be printed upside down so...

The SN04 bracket that comes with the dual extruder option for the Tevo Tarantula doesn't offer much height adjustment. This bracket lets you slide the bracket up and down on the screws that hold it to the heat sink. In addition to that you still...

This bracket is similar to the laser-cut bracket that ships with the model, but this one is for DUAL HOTENDS. The hotend which fits with this model is the one which ships with the TEVO. The best way to fabricate this bracket is with a CNC...

Having a Tarantula with dual stock extruder, i need a fan duct that can cool both hotend but lets me enough clearance to have a look at filament fusion and layer construction. That is how the the "Fang Duct" was born...and no the "g" is not a mistake...

Having a Tarantula with dual stock extruder, i need a fan duct that can cool both hotend but lets me enough clearance to have a look at filament fusion and layer construction. That is how the the "Fang Duct" was born...and no the "g" is not a mistake...

Things you are going to need in order to get this done: I HIGHLY RECOMMEND USING HARDWARE WITH INTERNAL HEX VS PHILLIPS OR FLATHEAD The following parts were sourced from Amazon, Openbuilds, and any Hardware Store Flexion Dual Extruder Kit... Duh! Be...