tevo little monster 3d models
180394 3d models found related to tevo little monster.thingiverse
This is the stock Tevo Little Monster effector plate. I've included the STL, IGS, and SLDPRT file. I used the DWG files found below to draw the parts in Solidworks 2016. Please note that if you want to open the Solidworks file you will need...
thingiverse
I needed a cover for the box on a DuetWifi converted Tevo Little Monster and wanted to spice it up a bit. ... I extended the openings cause I couldn't get my finger into reach to the sd card which will also allow the case to be opened while plugged in.
thingiverse
Here's my enclosure kit for TEVO Little Monster You need 2.5mm-thick-polycarbolate panels (such as plexyglass) in which you must cut : 6 x (1000 x 66mm) 2 x (1000 x 159mm) 2 x (1000 x 319mm) Note : You can also use from 2.4 to 2.6mm thick panels You...
thingiverse
This mod allows you to get more height on the z of a tevo little monster.
thingiverse
Tevo Little monster cover for the carriages. ...stops cables from getting caught
thingiverse
Belt tensioning mechanism for the tevo little monster. ...The baseplate is being screwed into the cbeam and the part that holds the bearing is attached with a bolt.
thingiverse
The belt on the Tevo Little Monster are attached to the Vertical Carriage with zip ties. My concern is that its not rigid enough and will flex. Therefore I made this small clip/tie to make a safer mounting of the belts. ...Its not perfect but might be...
thingiverse
The instructions I've provided are for a Duet-powered Tevo Little Monster. Perhaps someone can comment on how to work with the stock Smoothie. Here's a head start: http://smoothieware.org/switch#pause-when-out-of-filament and...
thingiverse
Another cover for the stock controller board box on the Tevo Little Monster Delta 3D printer. It fits the Duet3D controller board (not the stock MKS). The concept is simply to make use of the two blue LEDs hanging about, illuminating the Tevo logo...
thingiverse
Not all of my filament spools fit the shaft of the original Tevo little monster spool holder. I therefore designed a multi-spool holder where I re-used the bracket. It is made so I only need to make a new shaft if I get a filament spool with other...
thingiverse
Replacement effector for allow a chimera (or cyclops) hotened to be used on a Tevo Little Monster. After printing, use an M4 tap to tap the holes to mount the delta arms. Print with a low layer height and with interior perimeters before...
prusaprinters
... Do not use these files if you do not understand what the G-code commands contained are good for. Warning: Do not try to use this with any printer other than the Tevo Little Monster. ...By doing so, you would risk to severely damage your printer.</p>
thingiverse
... Do not use these files if you do not understand what the G-code commands contained are good for. Warning: Do not try to use this with any printer other than the Tevo Little Monster. ...By doing so, you would risk to severely damage your printer.
thingiverse
Wanted to tidy up the cabling on the TEVO Little Monster, hiding all the modular connections in an easy to reach place, but didn't want to involve using flexible filaments. I re-sheathed all the cabling with the cable braid used from a generic PC mod...
thingiverse
Little bracket to hold the LEDs for eyes on the Little Monster's Tevo logo.
thingiverse
Eclairage Pour Tevo LM Orientable verticalement 2 bandes LED 7 cm 24Volts ou LED 11 Cm (reflecteur 110-stl) 2 vis M4 + Tnuts 2 vis M4 20 mm + écrou Lighting for Tevo LM Vertically adjustable 2 LED strips 7 cm 24Volts or LED 11 cm (reflecteur-110-stl)...
thingiverse
(if your a wood worker you already know how to do this) 3 short lower panels 3x 13 1/8 to 13 1/4 better to be a little long here 6 short side lower panels 2 11/16 x 2 3/16 there are little brackets to go on the top and bottom to hold the larger plexi...
thingiverse
Tevo Little monster bed file incl. ...source for autodesk inventor Leave a feedback ;-)
thingiverse
Remixed this nice model to work with my TEVO Little Monster.
thingiverse
I made my own panel of Duet Maestro for Tevo Little Monster by using OnShape. ... OnShape is my favorite CAD Tool.
thingiverse
A cover for the steppermotors on the Tevo little monster, watch Design Prototype Test's video to see them in action: https://www.youtube.com/watch?v=HLqlx-hx6eE&t=249s
thingiverse
02.03.2018: Add short version, for one spring Накладки на штанги 3D принтера TEVO Little Monster для установки пружин как замена скотчу на который были одеты пружины. Печатать 12 штук для верхних и нижних концов штанг. ... 02.03.2018: Добавлена...
thingiverse
I wanted to add OctoPrint to my Tevo Little Monster so I made this Bracket / Holder / Case for a Raspberry Pi. You can power the Pi directly over the power supply of the Little Monster. ...I used a Raspberry Pi 2.
thingiverse
Made up this filament cleaner as I wanted something to clip onto the underside of the Filament Guide I use for my Tevo Little Monster. This item clips onto the corrugated cord and is dimensioned to line up with this item. ...
thingiverse
#TEVO Little Monster: Extruder Threading Improvement Tired of the filament not threading properly? These two parts are a big help. The arm has a much tighter filament barrel which helps keep the filament from going off to the side. The tube...
thingiverse
Box for TFT28 LCD screen delivered with TEVO Little Monster. No support needed. ...Release Notes 2017-03-22 : added a foot version for M5 bolts (M4 version still available - check name) New mount Print Settings Rafts: No ...
thingiverse
This Is a Spoll holder for Tevo little monster it replaces the metal holder on top. This way you can use up to a 3K spool. It will also lock the filament spool inplace so there is no way you can have it fall off the top. ...the right side uses the...