tevo little monster 3d
1753420 3d models found related to tevo little monster 3d.thingiverse
Arm end cover TEVO Little Monster 3D printer for mount springs, for replacement of an adhesive tape on which springs are mounted. Print 12 pcs for top & bottom end of arms. 02.03.2018: Add short version, for one spring Накладки на штанги 3D принтера...
thingiverse
Another cover for the stock controller board box on the Tevo Little Monster Delta 3D printer. It fits the Duet3D controller board (not the stock MKS). The concept is simply to make use of the two blue LEDs hanging about, illuminating the Tevo logo...
thingiverse
This is a top plate hole cap for Tevo Little Monster 3D printer, this cap have 2 hole for filament guide and tube for cable management(ziptie). You can also set the holder PTFE tube(screw it in). Mount 2x M3x14(16) screw. Это крышка для отверстия в...
thingiverse
Little bracket to hold the LEDs for eyes on the Little Monster's Tevo logo.
thingiverse
This is the stock Tevo Little Monster effector plate. I've included the STL, IGS, and SLDPRT file. I used the DWG files found below to draw the parts in Solidworks 2016. Please note that if you want to open the Solidworks file you will need...
thingiverse
I needed a cover for the box on a DuetWifi converted Tevo Little Monster and wanted to spice it up a bit. ... I extended the openings cause I couldn't get my finger into reach to the sd card which will also allow the case to be opened while plugged in.
thingiverse
Here's my enclosure kit for TEVO Little Monster You need 2.5mm-thick-polycarbolate panels (such as plexyglass) in which you must cut : 6 x (1000 x 66mm) 2 x (1000 x 159mm) 2 x (1000 x 319mm) Note : You can also use from 2.4 to 2.6mm thick panels You...
thingiverse
Eclairage Pour Tevo LM Orientable verticalement 2 bandes LED 7 cm 24Volts ou LED 11 Cm (reflecteur 110-stl) 2 vis M4 + Tnuts 2 vis M4 20 mm + écrou Lighting for Tevo LM Vertically adjustable 2 LED strips 7 cm 24Volts or LED 11 cm (reflecteur-110-stl)...
thingiverse
first quick design i try to print it in 1 part if it's a little hard ,i'll redesign it in 3 or 4 parts update : cut in 5 parts !
thingiverse
(if your a wood worker you already know how to do this) 3 short lower panels 3x 13 1/8 to 13 1/4 better to be a little long here 6 short side lower panels 2 11/16 x 2 3/16 there are little brackets to go on the top and bottom to hold the larger plexi...
thingiverse
This mod allows you to get more height on the z of a tevo little monster.
thingiverse
Tevo Little monster cover for the carriages. ...stops cables from getting caught
thingiverse
Belt tensioning mechanism for the tevo little monster. ...The baseplate is being screwed into the cbeam and the part that holds the bearing is attached with a bolt.
thingiverse
The belt on the Tevo Little Monster are attached to the Vertical Carriage with zip ties. My concern is that its not rigid enough and will flex. Therefore I made this small clip/tie to make a safer mounting of the belts. ...Its not perfect but might be...
thingiverse
... to keep an eye on my designs as I'm currently uploading parts for that printer successively. Also check 3Dvice's Little Monster parking brake: https://www.thingiverse.com/thing:2721009 This is one essential part no Little Monster should be without!
thingiverse
The instructions I've provided are for a Duet-powered Tevo Little Monster. Perhaps someone can comment on how to work with the stock Smoothie. Here's a head start: http://smoothieware.org/switch#pause-when-out-of-filament and...
thingiverse
Not all of my filament spools fit the shaft of the original Tevo little monster spool holder. I therefore designed a multi-spool holder where I re-used the bracket. It is made so I only need to make a new shaft if I get a filament spool with other...
prusaprinters
This is a cap covering the pulley sides of the Little Monster's (or any equivalent delta printer's) X, Y and Z motors, just to keep dust off the gears and make the printer's look a little less "raw".Application is easy: Just print it, slide it onto...
thingiverse
Replacement effector for allow a chimera (or cyclops) hotened to be used on a Tevo Little Monster. After printing, use an M4 tap to tap the holes to mount the delta arms. Print with a low layer height and with interior perimeters before...
prusaprinters
... Do not use these files if you do not understand what the G-code commands contained are good for. Warning: Do not try to use this with any printer other than the Tevo Little Monster. ...By doing so, you would risk to severely damage your printer.</p>
thingiverse
... Do not use these files if you do not understand what the G-code commands contained are good for. Warning: Do not try to use this with any printer other than the Tevo Little Monster. ...By doing so, you would risk to severely damage your printer.
thingiverse
Wanted to tidy up the cabling on the TEVO Little Monster, hiding all the modular connections in an easy to reach place, but didn't want to involve using flexible filaments. I re-sheathed all the cabling with the cable braid used from a generic PC mod...
thingiverse
This is a replacement face plate to go with the Tevo LM specifically for the Stock MKS board.
thingiverse
You can see how I configured smoothieware at: https://github.com/crpalmer/3d-printing/blob/master/tlm/smoothieware/config Update the start.gcode that you use for the new sensor by removing all references to the servo and updating the G30 Z___ offset...
thingiverse
Tevo Little monster bed file incl. ...source for autodesk inventor Leave a feedback ;-)
thingiverse
Remixed this nice model to work with my TEVO Little Monster.
thingiverse
I made my own panel of Duet Maestro for Tevo Little Monster by using OnShape. ... OnShape is my favorite CAD Tool.