tf2 direct hit 3d models

I designed a custom bracket to support the installation of a Titan Extruder Clone on my CR-10S Pro, upgrading it to a direct drive system. ...The bracket accommodates a 23mm pancake stepper motor for precise and efficient operation.

Remix of the filament guide from Matt, tailored specifically for use with a Direct Drive modded Ender 3 Pro. ...To achieve this, I shortened the arm and introduced a precise 1.8mm gap.

I created this cable holder to hold cable correctly with a sotck direct drive motor on the extruderYou need to print the axis to hold them together or use an M5 screw

A direct-drive extruder model features a head placement, and upon functioning, I'll share a video. ...The initial design is by Tito, which can be found at http://www.thingiverse.com/thing:110269.

Direct Cable Holder Installation for Ender 3 Requires an M3x8 Screw. A Quick and Easy Solution to Keep Your Cables Organized. ...Watch the Step-by-Step Guide on YouTube.

I designed a Direct Drive mount specifically tailored for the Ender3, ensuring seamless compatibility with the CR10 printers. ...The creation targets the Dual Drive mount variant exclusively, distinguishing it from its standard counterpart.

Small edit to remove the bowden holder on top. ...Since the old mount had a bowden holder, it can mess with your direct drive placement. ...This removes the bowden holder.

Remixed the gantry clip for fitting together with the direct drivinator of Mediaman. Also made it a bit longer for better clamping. ... The original clip was not fitting and it broke my base.

Filament sensor for Ender 3 for direct drive extruder. ... What you need: - pen spring - ball bearing 688 - ender end stop - silicone grease (optionaly) - screw m2 x2 - threaded insert m2 x2 - m3 screw and nut x3

resized the knob end to be smaller to accommodate the smaller space with the direct drive setup. the shaft hole was left unchanged but didnt fit without filing etc. the hole was to small. Palodion... ...thanks for the design.

Spacer for the BLTouch Mount on the TriangleLabs Direct Drive Extruder Kit. The Springs Are Not Required, as a 4mm Spacer Is Sufficient. ...The Real BLTouch Has a Z Probe Offset of Approximately 2mm.

I whipped up a custom mod for myself, figuring I'd share it with others. ...This mod is designed to fit the Petsfang Direct Drive Mount rather than the Titan one, allowing you to utilize your stock extruder seamlessly.

7/6/21- Direct drive is still off. working on new design all together. source file - https://www.thingiverse.com/thing:3589452 Had to modify the design. Extrude was off by 6mm to hot end. ... Added EGA

This is is a remix for the linear rails version of the Microswiss direct drive extruder kit for wire and strain relief. ...If you find any issues let me know.

When switching the D-Bot over from Bowden to direct drive, human operators need to adapt the X endstop on the carriage. ... Print Settings: Printer: D-Bot Rafts: No Supports: No Resolution: 0.2mm Infill: 70%

[Source with the left side of the bracket](https://www.myminifactory.com/object/3d-print-139464) [The mating part of the flexible cable channel](https://www.thingiverse.com/thing:4604859) Модернизированный правый кронштейн для direct Flying bear...

It increases the speed and quality of printing, converting the extruder with direct filament. getting to print at 120 mm / s without losing quality. The motor fastening screws have to be replaced by 3x12mm screws. Increases the speed and quality of...

After converting from bowden to direct drive I needed to keep my cables from getting pinched or drooping onto the back side of the build platform. Its designed to snap over the extruder drive motor with the tang to the back. ...I used a zip-tie...

I purchased the Enomaker Direct Drive Kit from Amazon, but to my surprise, it lacked a strain relief system for the wires connecting to the hot end. The kit includes a 3mm thick spacer that mounts behind the extruder arm, so I created a custom...

Using this part to move the spool inside the cage, while using linked part below to direct the filament: https://www.thingiverse.com/thing:3872001 The only extra parts you will need are 4 pairs of m4 machine screw + t-slot nut Here is the assembly...

With its robust build and direct drive extruder, it's capable of producing high-quality prints with ease. You can also find similar instructions below on my Facebook page. ...Just follow this link to get access to all the information you need:...

Direct Drive Setup Guide: Securing Filament on Your Ender 5 Get a solid grip on your filament with our simple direct drive setup for the Ender 5. This guide shows you how to keep the filament in its original position. For the Single Bolt Version,...

Since this printer is getting a direct drive upgrade, I decided to take advantage of the situation and design something that would integrate seamlessly into the existing setup. ...This new spool holder will be compatible with any 2020 extrusion piece,...

Using this part to move the spool inside the cage, while using linked part below to direct the filament: https://www.thingiverse.com/thing:3872001 The only extra parts you will need are 4 pairs of m4 machine screw + t-slot nut Here is the assembly...

A combination of a couple of different models:Longer LK4 / Diggro 3 Direct Drive Remixby ultrastickmanBlowie Mk1 | custom cooling for |Alfawise U30 & U20|Longer lk4 pro|by DonJon99Blowie Mk2 | Custom Fan Duct for Alfawise U30 & U20 | Longer...

I wanted an option to direct mount using #8 or *#10 drywall screws directly without the need for the dovetail style mounting bracket. I do not mind if the screwheads are visible, so I remixed the original design into this. ... *No Supports needed...

Direct Drive Extruder Lever Reinforcement When operating the extruder lever in direct drive mode, it's essential to reinforce the component to ensure optimal performance. Initially, I encountered issues with deformation due to excessive heat when...

... new hardware. Through resourceful problem-solving, I devised a temporary solution that would allow me to utilize the E3D Direct mount on my Anet A8, effectively expanding its capabilities as both a primary 3D printer and a secondary laser engraver.

... Only! The first extruder remains as a Bowden setup, while the second extruder is set up for direct drive. The Mainboard must be shifted slightly to the right due to the size of the extruder handles. ... Updated 02/2019 - Improved Version.

Adapter Guide for System Bowden to Direct for 1.75mm Filament Diameter Version 2 is designed for a hotend E3Dv6 to be mounted on the gtcdma support, available at https://www.thingiverse.com/thing:1383913 This adapter guides filament through a 4mm...