tft enclosure 3d models

The case has a simple door opening and closing structure for easy access and plugging in of usb devices, the mounting holes in the case itself are the same as the FLY TFT V1 (maybe useful?). . It also supports Fly3D's M2WE board (EMMC storage and...

This is a replacement cover for the V-Minion electronics enclosure with a mount for BTT pitft43 (or compatible). ... The hinge is held together by some M3 bolt at least 22mm long.

The design is pretty similar to my other design which uses a smaller 2.2" screen instead: https://www.thingiverse.com/thing:2832880 The user 94Z28 published a remix, which fits a larger Node MCU board: https://www.thingiverse.com/thing:3887862 The...

The challenge I faced was finding an ideal case for my Raspberry Pi 2, which demands better performance, especially when paired with OctoPrint, a camera module, and OctoPiPanel on the Adafruit TFT display. Given that I had a Raspberry Pi 1's PiTFT...

HypnoKid is an Alternative Mount for the BW 7 Inch TFT Screen. Its counterpart has been modeled to fit a year-old BMW E90/3 Series front seat head-rest - specifically, a 320D in our case. I initially tried mounting it in our '97 VW Sharan VR6 but...

This housing enables the installation of a touchscreen with octopi/octoprint_tft on Prusa MK3s printers, specifically designed for space-constrained environments where the touchscreen must be mounted on the side of the printer. It sits atop the power...

This is a remix of @pedroamz great design for the bigtreetech 2.4" TFT touchscreen https://www.thingiverse.com/thing:3827565. Bigtreetech have changed their hardwaredesign since pedroamz has created his case and some things have been moved like...

I made this to contain a 1.8"TFT screen ST7735 and attach it to a project box which contained an Arduino. The template allowed me to precisely cut out the holes for the cables and the screws to hold it in place and then seal the main box from the...

Case for the ESP32 D1 mini and a TFT 3.2 inch (ILI9341). I designed this to connect a ham radio transceiver FT-817 or FT-818 to the display. The USB port of the ESP32 will later only be used for programming, while the cable on the back is connected...

The intent is to power off the printer and simply flip this recessed switch (accessed thru the last vent slot alongside the USB connector) using a pen or small screwdriver, to disable the TFT screen for flashing. I did not want block any airflow...

After damaging the controller in my X3S I bought a MKS Robin V1.0 Controller from Banggood which came with the TFT 3.5 screen and a WIFI Adapter. The screen is so much nicer than the original Xvico one and I loved the fully customisable firmware...

I crafted an electronic enclosure specifically tailored to house the electronics of my Prusa P3 Steel printer. ...Unfortunately, I couldn't locate the MKS Integrated board, so I designed this custom housing for a 60mm fan and the MKS Mosfet instead.

This is a remix of @pedroamz great design for the bigtreetech 2.4" TFT touchscreen https://www.thingiverse.com/thing:3827565. Bigtreetech have changed their hardwaredesign since pedroamz has created his case and some things have been moved like...

This is a case for a ST7735 TFT display including the cable connector, and an Arduino Nano or SBC-NodeMCU board. The display as well as the MCU board can be put in place without screws or glue. There's space for several components: * A DHT22...

The overhang makes it a bit of an odd case variant, but it works fine and actually doesn't look bad at all once it is in a case. The situation is that I wanted to use the Pi 2 due to the better performance, which is especially needed when running...

... will also fit all 3.2-inch displays perfectly. These parts are engineered to be mounted directly onto any flat surface, providing an elegant exterior design that stands outside of the enclosure. ... The fan casing is purely decorative in nature.

Having upgraded my CR10S with a BTT 35 TFT I was frustrated that the existing Control Box Limited the accessibility of some of the ports and therefore features of the Display. I therefore designed this console to allow access to the Display USB &...

Having upgraded my CR10S with a BTT 35 TFT I was frustrated that the existing Control Box Limited the accessibility of some of the ports and therefore features of the Display. I therefore designed this console to allow access to the Display USB &...

To assemble the enclosure, widen the mounting holes on the board using a 4mm drill bit to ensure there's some extra room for adjustment. The enclosure is secured by four 8mm M3 screws. Apply a small amount of super glue between the body and top...

I designed a custom enclosure for my Arduino Mega board, Sainsmart shield, and 3.2 inch TFT touchscreen, creating a sleek DIY pixel stick equivalent from scratch.

OUTDOOR ENCLOSURE

Electronics Enclosure

This enclosure is designed specifically for the KUMAN 7" LCD screen, which can be purchased online at http://www.kumantech.com/kuman-7quot-tft-lcd-capacitive-touch-screen-hdmi-800480-for-raspberry-pi-3-2-model-b-rpi-1-b-a-bb-black-pc-sc7b_p0024.html...

YouTube: https://www.youtube.com/watch?v=jy7a-z19UEQ NEW UPDATE April 8, 2016 – Added new parts for Adafruit 2.4" TFT Feather Wing This case is specifically designed to house the Adafruit Feather and can be used by anyone looking to put their project...

If you're interested in replicating this build, here are some key components I used: The PSU mount was sourced from Thingiverse, specifically this design: https://www.thingiverse.com/thing:2529702 For the TFT mount, I relied on this clever solution:...

The radio itself was built using two speakers, a 128x160 TFT-screen with a blue PCB, and a rotary controller. I mounted the PCB on the base using nylon standoffs, securing other components in place with double-sided adhesive tape and hot glue where...

Internal enclosure - a slimmer version of the internal enclosure for the arduino nano, max and dimmer. Compatible with the nano and wago 221’s. Sits nicely behind at the back of the pump and doesn’t hit against the funnel. The holes for wiring face...

The 22 kV Enclosure is specifically designed for outdoor use in electrical substations, providing protection to high-voltage equipment (excluding the actual apparatus).

Stacked enclosure for Arduino Mega2560 and high-quality 3.5-inch IPS TFT display with ILI9486 or ILI9488 controller, featuring a crisp 480x320 resolution and robust endcaps for added protection.

So you can look at this as a customizable enclosure , but I made this as a enclosure for my wifi router UPS this can hold a 3s battery pack in triangular configuration and then the lower section can house all the other components like boost...