tft squink 3d models

This housing enables the installation of a touchscreen with octopi/octoprint_tft on Prusa MK3s printers, specifically designed for space-constrained environments where the touchscreen must be mounted on the side of the printer. It sits atop the power...

Case for the ESP32 D1 mini and a TFT 3.2 inch (ILI9341). I designed this to connect a ham radio transceiver FT-817 or FT-818 to the display. The USB port of the ESP32 will later only be used for programming, while the cable on the back is connected...

The intent is to power off the printer and simply flip this recessed switch (accessed thru the last vent slot alongside the USB connector) using a pen or small screwdriver, to disable the TFT screen for flashing. I did not want block any airflow...

This is a remix of @pedroamz great design for the bigtreetech 2.4" TFT touchscreen https://www.thingiverse.com/thing:3827565. Bigtreetech have changed their hardwaredesign since pedroamz has created his case and some things have been moved like...

This is a case for a ST7735 TFT display including the cable connector, and an Arduino Nano or SBC-NodeMCU board. The display as well as the MCU board can be put in place without screws or glue. There's space for several components: * A DHT22...

The overhang makes it a bit of an odd case variant, but it works fine and actually doesn't look bad at all once it is in a case. The situation is that I wanted to use the Pi 2 due to the better performance, which is especially needed when running...

This is an Enclosure for Bigtreetech SKR1.3 and TFT35 V2.0 targeted to MPCNC application. BOM: SKR 1.3 TFT 35 V2.0 Fan 40x40 8x Selftapping screws 2.5 x 10 mm You can find the MPCNC modification of BTT TFT35 FW a the following link:...

Having upgraded my CR10S with a BTT 35 TFT I was frustrated that the existing Control Box Limited the accessibility of some of the ports and therefore features of the Display. I therefore designed this console to allow access to the Display USB &...

Having upgraded my CR10S with a BTT 35 TFT I was frustrated that the existing Control Box Limited the accessibility of some of the ports and therefore features of the Display. I therefore designed this console to allow access to the Display USB &...

If you're like me, and I know I'm not alone, printing out https://www.thingiverse.com/thing:2471701 only to discover that your Adafruit 3.5" PiTFT doesn't fit is a frustrating experience. Don't worry, I've been there too. I created a remix of the...

3d models of Zahori character Urf version For a height of 10 cm or 4 inches.

Another TFT35 casing. This one is designed for the Makerbase Robin Nano35 Printed with PLA @layer height 0,15mm. ... The bracket and cooling duct (for Delta printer) can be found here: https://www.thingiverse.com/thing:4608024

28/5000 makerbase tft35 display model

Fusion360 drawing at https://bit.ly/3ahuRlR

This is a straightforward project for the MKS TFT32 L V3.0, where the display sits atop the standard 3D printer screen. A notable departure from other cases is the placement of the display above the original display, allowing users to easily compare...

This enclosure is optimized for a 0.6mm nozzle. The two pieces snap together. There are holes in the top piece for heated M3 threaded inserts that are roughly 4.6mm x 5.7mm in size. ...6mm M3 socket head cap screws can be placed through the holes in the...

Displaying live footage from a sleek Sidewinder X1, expertly captured by the high-performance Tevo Tornado Pro. ...The rugged housing is designed to seamlessly integrate with any 3D printer featuring an SKR board, allowing for maximum flexibility and...

A non-slanted version of the below model. it is also slightly shallower to make it more handheld. the available space below screen is about 25mm. ILI9341 Screen. ... https://www.thingiverse.com/thing:3461768

Human interfaces don't get much more advanced than this cutting-edge technology - The NNOLUX 7-inch touchscreen display kit for the Raspberry Pi, AT070TN90! Equipped with a wide range of innovative features and high-resolution display capabilities,...

Here's a creative solution to keep cables organized and hidden from view while still allowing easy access: design custom cable organizers that fit snugly behind computer screens. These organizers can be crafted using 3D printing technology, which...

This creation was crafted within Tinkercad's intuitive platform. ...Edit and refine it instantly at https://www.tinkercad.com/things/5ZsQIHUz0gK.

TFT28 LCD CASE AND V1.4 MSK BOARD 50MM FAN Print Settings Rafts: Disabled Supports: Enabled Resolution: Adjustable from 25 to 100% Infill: Solid (100%) Notes: The MSK Board measures 147mm in length and 89.8mm in width

Mounting option 1: 1pcs M5x20mm 4pcs M5x10mm 1pcs M5 tnut Mounting option 2: 5pcs M5x20mm 1pcs M5 Tnut The 4pcs M5x20mm will replace the 4pcs M5x10mm used in the front of printer. The 4pcs M5x10mm screw will then be used to mount...

This time there is no puny thin walls, too steep overhangs and friction fitting. Overall design is inspired by nehiLo's KP3S mount and select few(heights and fillets for screen cover) measurements are taken from there, shape of screen box is...

modul

Credit goes to Jim Sheldon who designed this case. ... Latest files are v9 and V11

Credit goes to Jim Sheldon who designed this case. ... Latest files are v9 and V11

This case is centered around a compact Raspberry Pi A+ and an Adafruit PiTFT 2.4" HAT, designed to be as diminutive as possible while achieving a height of just 17mm. The project draws inspiration from Adafruit's innovative Pocket PiGRRL. ... To achieve...

A small mountable holder for a fasttech LCD module. Mounting pins are a little tight but can be snapped off if not needed. Mount holes are designed for assorted leg or spacer designs. Holes are 5mm dia, 34mm apart and hole centre 5.5mm from edge if...