tft squink 3d models

This is a custom enclosure and partially closed case for a 7-inch touch TFT display with a resolution of 1024x600 pixels, which I purchased from AliExpress for 40 euros. The details of the design are included in the attached drawing. On the images...

DescriptionER-TFTM043-7S is 800x480 dots 4.3 "color tft lcd module display with SSD1963 controller board,full viewing angle.superior display quality and easily controlled by MCU such as 8051(C51), PIC, AVR, ARDUINO,ARM and Raspberry PI .It can be...

I have the BigTreeTech TFT 3.5 E3 touch screen and the original case did not have holes for the USB and SD card slots on the Touch Screen, so I modified it. Two changes made from original case: Added access holes for the USB port and Memory Card...

This is a case for the Wemos D1 Mini (https://wiki.wemos.cc/products:d1:d1_mini) plus its TFT 2.4 Touch Shield (https://wiki.wemos.cc/products:d1_mini_shields:tft_2.4_shield). The design was intended for landscape mode, but I only have a demo working...

A 17.8 cm (7") TFT LCD touch display, with 800 x 480 pixels resolution, is used. The case is compatible with it. The special thing about this design is that the Raspi is mounted lengthwise. The USB connectors and network connector can be accessed...

The centerpiece is a sleek 2.4-inch TFT clock with a vibrant 240 x 320 pixel display, powered by a reliable 3.7-volt lithium battery. To bring this project to life, I required the following key components: one high-quality 2.4-inch ILI9341 display,...

DescriptionER-TFT4.58-1 is stretched bar-type 4.58-inch IPS TFT display, featuring a sharp resolution of 320x960 pixels. With an impressive contrast ratio of 800:1, it excels in rendering deep blacks and vibrant colors, ensuring a visually striking...

DescriptionER-TFT3.95-1 is square 3.95-inch IPS TFT display, featuring a sharp resolution of 720x720 pixels. With an impressive contrast ratio of 800:1, it excels in rendering deep blacks and vibrant colors, ensuring a visually striking experience.

Raspberry Pi 3.5 TFT LCD touch screen holder is mounted into 2x 5.25 drive bay. USB cable could be wired to 10 pin USB port on motherboard or to back USB port. ...Holder was designed for Zalman Z5 case, but it should fit to any computer drive bay...

This is a remix of @JimbalNy's cover that I made in order to fit inside the cover the ESP01 wifi module, and I made in order to avoid crashes of bed's knob on the TFT. Now all the screws needed are M3. "Fit a TFT35 to your Sidewinder X1 without...

One of the standout features on MKS TFT screens is the capability to pause once you've exhausted your filament supply. This was a design I implemented using one of the three end stop switches I replaced when I installed my optical switches. It...

DescriptionER-TFTM0784-2 is 1280x400 dots 7.84 "color IPS tft lcd display with LT7683 or RA8876 controller board and optional capacitive touch panel,full view angle,superior display quality and easily controlled by MCU such as 8051(C51), PIC, AVR,...

This is a sleek, slightly tilted (and upright version included) holder for an Arduino-mounted ILI9488 3.5" TFT display with touch functionality and TF card reader integration. While it's not a comprehensive enclosure, it presents a more refined...

DescriptionER-TFT040-3 is square 4-inch IPS TFT display, featuring a sharp resolution of 480x480 pixels. With an impressive contrast ratio of 800:1, it excels in rendering deep blacks and vibrant colors, ensuring a visually striking experience. The...

Since I switched to klipper and didn't feel like figuring out the stock screen, I ended up using a Kuman 3.5" tft and a Pi3b+ for my klipper conversion. Though initially mounted separate with a usb cable connecting, I wanted to integrate it into...

DescriptionER-TFT3.99-1 is stretched bar-type 3.99-inch IPS TFT display, featuring a sharp resolution of 400x960 pixels. With an impressive contrast ratio of 800:1, it excels in rendering deep blacks and vibrant colors, ensuring a visually striking...

This is a remix of @JimbalNy's cover that I made in order to fit inside the cover the ESP01 wifi module, and I made in order to avoid crashes of bed's knob on the TFT. Now all the screws needed are M3. "Fit a TFT35 to your Sidewinder X1 without...

DescriptionER-TFTM035-6 is 320x480 dots 3.5" color tft lcd module display with ILI9488 controller and breakout board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry...

This is a compact LCD display enclosure designed specifically for the ST7735S 128x160 1.8" TFT screen. The unit features a sleek design that securely holds the LCD in place using a snap-down mechanism and four pegs. A rear spacer block ensures the...

DescriptionER-TFT3.71-1 is stretched bar-type 3.71-inch IPS TFT display, featuring a sharp resolution of 240x960 pixels. With an impressive contrast ratio of 800:1, it excels in rendering deep blacks and vibrant colors, ensuring a visually striking...

DescriptionER-TFT2.99-1 is stretched bar-type 2.99-inch IPS TFT display, featuring a sharp resolution of 268x800 pixels. With an impressive contrast ratio of 800:1, it excels in rendering deep blacks and vibrant colors, ensuring a visually striking...

Link to applicable page on main V1 Engineering site: https://docs.v1engineering.com/electronics/skrpro/ Link to chronicle of my LowRider v2 build on V1 Engineering forum:...

After printing my initial version, I realised it needed to be 2.7mm lower to match my cheap 3.5" TFT screen and also I wanted the edges to be rounder! You can see my screen in the make images, but it's likely others are the same thickness/height. ...

A case designed for the original Ender 3 a Raspberry Pi 4B and a 3.5" TFT screen that connects via the GPIO pins. It also comes with a holder for the stylus that comes with most of these screens. The holder snaps onto the stylus and holds it...

The sd card extender for the tft can be very short (about 15cm). Same for the usb. The sd card extender for the skr mini, in my case, had to be extended twice. About 70cm in total. I first assembled all the components in the housing, and then...

I had an application where I needed the LCD display to be separate from the Arduino (Wemos D1). This let me run a ribbon cable from the panel to behind where the arduino was mounted. I had almost no space for this. I initially tried beveled edges,...

Other Parts Screw: M2 4mm X2 M2 8mm X4

Updated the top moving the block above the Ethernet port to the other side. This makes a much better fit. ... Enjoy!

<p>Only a small remix for T-Nut Extrusion</p><p><strong>If you like to, check out </strong><a href="https://www.prusaprinters.org/social/194698-max-siebenschlafer/prints?o=liked"><strong>my other designs</strong></a><strong> too!</strong></p>

Display