the bq 3d models

... ... After Zowi broke a foot, I redrew the foot and divided it in 3 parts, so you can print just the broken part. Video of the robot dancing with its new foot: https://youtu.be/XbNczGihgMg Note: I don't have any relationship with BQ

Foot to adapt the Spool Holder Tush to the BQ spool of differential diameters on the sides Pie para adaptar las bobinas de BQ que tienen diferente diametro cada lado al sporte de bobina Tush

I was trying to find a filament clip that would work well with the BQ spools and decided to create my own which takes advantage of the holes around the edge. ... This is for 1.75mm filament

Updated to use for the BQ Prusa i3 Hephestos with original extruder/hotend bracket and end clip for cable chain Update v1.1: Added support to clip for cable chain

Case for the bq Aquaris X I didn´t found a case on thingiverse for my new phone so I made one. ...Fits pretty tight, so I recommend to use Flex-Filament.

I designed this thing as an 300gr bq spool holder. ...It works for spools with a hole of 4.5cm as the bq 300gr spool. You need to print 2 of this, one for each side of the spool. ... EDIT: I realized that it also works for bq 1kg spools.

Support for filament reel anchored on the top of the 3D printer only for the BQ Witbox model. ... Witbox Witbox 2

Simple wall mounted support for the BQ Aquaris E5 Work in progress Print Settings Printer Brand: Prusa Printer: Prusa Steel Supports: No Resolution: 0.4 Infill: 10%

piece needed for coils of the brand bq

I designed this as a simple and space saving way to achieve better stability in the bq Hephestos 2 printer. Designed for M6 Hardware. Print 1x front, 1x rear and 2x bracket. ... 1-Screw hinges loosely together 2-Press slot onto frame 3-Insert M6...

... works fine. https://www.youtube.com/watch?v=d3_24Bz5s_Q I also changed the BQ connectors to JST XH2.54 and MOLEX KK396 connectors. ...I attached a KK396 header to the original heater cartridge cable in order to use the original hotend again.

This is a new blower for the BQ Witbox (both models 1 and 2) Compared to the original is more efficient, more powerful and concentrated. old blower used to cool down the hot.end, causing jamming. this one solves the problem. Only hits the base with a...

The original included endstop is not a perfect fit for the BQ Prusa i3. ...This one fits ands aligns perfectly.

This is a filament feeder for the bq Hephestos 2. THe tollerences are a bit loose for clipping it on, just add some masking tape for it to grip. Will fit 4mm o.d. ...ptfe

... of https://www.thingiverse.com/thing:2011130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2011130 For the new BQ spools that are crystal like material. As soon as i print it i will upload more photos. ...

UPDATE 17/01/2019: It has been included the adapter for the BQ filament with 300 grams. Therefore there are two models: Short: 300 grams format Long: 1000 grams format This desing allows to use spool holders with bearings (e.g:...

UPDATE 17/01/2019: It has been included the adapter for the BQ filament with 300 grams. Therefore there are two models: Short: 300 grams format Long: 1000 grams format This desing allows to use spool holders with bearings (e.g:...

This little project of mine is basically a "modification" to be able to use the BQ reels, on the MakeRoll designed by Maurino Web and Marco Spaccialbelli that you can find at this address https://github.com/3dingegno/MakeRoll As you can see from the...

... BQ Hephestos. ...It is an altered version of the original BQ X axis parts. ...Requirements: 8mm lead screw (THSL-300-8D) Flexible Coupling 5x8x25mm M3x12 (or M3x10) screws Print Settings Printer: BQ Hephestos Supports: Yes Resolution: 0.2 Infill: 70%

https://www.youtube.com/watch?v=cdfAlMr0BQY rubber o'ring was replaced with flex filament battery holder: https://www.thingiverse.com/thing:2668159 marble caster: https://www.thingiverse.com/thing:8959 Modification of a robot model that uses...

Adaptor to recycle some components from the mono block extruder from the bq Prusa i3 to upgrade the extruder nozzle to the J-Head type.

This is a playing exercise for me. ...That were the faceplate for the bq Hephestos 2 3D printer. Print with PLA or with every material you want. ...I prefer to infill it with 100%, because infill >5% doesn´t save much time or material.

... I am learning to use FreeCAD and designed a base to put it under one of the parts of the TUSH and leveling them to set both sides of the bq spool perpendicular to the table again I've printed with 15% gyroid infill and 0.28 resolution and went fine

TL Smoother holder for the BQ Hephestos 2. Made this just to give TL smoother a try on this printer. Replaces the Zum board cover. Its slightly higher but is OK for clearance of the bed. Latest version I added two tabs that help it clip in place. ...I...

V2 Nouvelle version du dessin plus efficace This adapter allow the use of the new BQ's spool to be used on the " Reel support for Hephestos " ( https://www.thingiverse.com/thing:2478932 ) or any other spool support that can't use spool with uneven...

BLTouch sensor mount for the BQ Hephestos. It's a remix of the meie1kyl version for the new version of BQ Hephestos, with only 2mm of thickness. ...You need: 2x Screws M3 x 20 Print Settings Printer: BQ Hephestos Supports: Yes Resolution: 0.2 Infill:...

This is a spool holder for the BQ Hephestos 2. But you can make it for another 3D printer... You need to print one time the 11 *.obj files , except the number 04 ( x2 ) and the 07 ( x6, if you want to have 3 spools ) ( this part 07 is for BQ spool...

... adjust perfect. I did it with FreeCAD. In the second version I am going to change the "bq" text for "fucking spaniards", like in the add http://www.youtube.com/watch?v=n3OmaQkOXfE Y la tercera es mas alta. ...Además he colgado el archivo de FreeCad.

I broke another spool holder trying to **force** the BQ filament spool, hence why I've designed this holder. I ended up using a printstik stuck down with double sided tape to hold the BQ filament while I quickly printed this holder. There are 2...

i changed the orignal BQ Filament Holder to use the Compact Spool Holder with Bearing Support, http://www.thingiverse.com/thing:1322123 Print Settings Printer: Hephestos Prusa i3 Rafts: No Supports: No Resolution: 0.1 Infill: 20