thermaltake core p3 parts 3d models
561469 3d models found related to thermaltake core p3 parts.grabcad
this is from one of the most popular computer partthe Thermaltake Core P3 - Noir
thingiverse
I created a nice cover for the PSU cables for the Thermaltake Core P3. Hope you like it. ... Two M3 nuts with washers are used to mount it
thingiverse
This is a blank cover plate for the big holes in the Thermaltake Core P3 case. I have my radiator mounted on top, and have no 2.5" drives to mount, so I decided to cover these holes for a more finished look. ...Covers can be screwed in from backside...
thingiverse
Rad mounts that hang on standoffs for Thermaltake core P3. ... Untested on Core P%
thingiverse
Hung a 3x120mm radiator between the standoffs of a Thermaltake Core P3 using these.
youmagine
This designs are about my Hackintosh which I built. ...These parts are for the aquacomputer filter and the EK-XRES 140 Revo D5 PWM reservoir and pump unit for my watercooling system. ... the full project is on my page: http://s-technologies.eu
cults3d
Support for fan or watercooling on Thermaltake Core P3 case Nvidia RTX 3080Ti is very large, so I adapted a bracket to move the watercooling more to the right. ... You can also attach to the bracket fans to create airflow.
thingiverse
Just a Headphone holder for the Core series. I made it by myself in lack of a ready one. ... There are versions with and without a cable holder.
thingiverse
So I created a bracket that uses the lower pcie slots and the existing holes in the PSU bracket to help pull the lower part of the bracket in line reducing GPU sag. ...Also fills in the open area below the bracket and top of the PSU making for a more...
thingiverse
Motherboard, PSU, and HDD rack mount for Thermaltake Core P5 and possibly P8 and P3. ... Comment if you need any help with this
prusaprinters
This leg for the Thermaltake Core Case P3 (https://www.thermaltake.com/products/chassis.html?cat=190) has a cutout for the power supply.Remixed Fromhttps://3dmakers.thermaltake.com/dwgallery.aspx?s=170
thingiverse
USB Hard disk slot mount for the Thermaltake Core P3 case. Likely also compatible with the Core P1 and Core P5 cases. ... The mount holds the drive at a 27 degree angle to allow space for the USB3 cable when multiple mounts are stacked.
thingiverse
This one should allow you to mount a 360mm X-flow radiator between two posts of your Thermaltake Core P3. It should work on any side of the case you like, presuming the location you choose doesn't impinge on any existing parts. A traditional...
prusaprinters
This is a mount to fit your EKWB DCC pump onto a Thermaltake core P3 case stock water bracket. This goes between the pump and the stock case bracket to mount securely and look good. ...This uses the stock EKWB DCC pump screws and a set of fan screws to...
thingiverse
This is a mount to fit your EKWB DCC pump onto a Thermaltake core P3 case stock water bracket. This goes between the pump and the stock case bracket to mount securely and look good. ...This uses the stock EKWB DCC pump screws and a set of fan screws to...
thingiverse
this/these is/are to support the 5mm glass panel on a Thermaltake core p3 open case, as adding extras like gpu hangar mounted display, glass mounted fan and top/side dust shroud seem to cause excessive lean on the chassis where legs mount. 40mm...
thingiverse
The Thermaltake Core P3 came with either tempered glass or plastic (like mine). The replacement glass with drilled mounting holes appears to be out of production and unattainable. My glass store balked at drilling holes so close to the edges. ...
thingiverse
7" LCD Screen Mount sized for Lebula 7" Screen (https://www.amazon.com/Lebula-Touchscreen-Raspberry-1024X600-Capacitive/dp/B07VNX4ZWY) for the Thermaltake Core Series Vertical PCIe Mount. I wanted to include a sensor panel on my Core P3 (may fit...
cults3d
The Thermaltake Core P3 case comes with a bracket for it's own branded pumps and kits, this was my quick solution to be able to mount a plate on the bracket that would also fit the Swiftech MCP50X perfectly so that it sat nicely in the case and you...
thingiverse
The Thermaltake Core P3 case comes with a bracket for it's own branded pumps and kits, this was my quick solution to be able to mount a plate on the bracket that would also fit the Swiftech MCP50X perfectly so that it sat nicely in the case and you...
thingiverse
This is a mount to fit your EKWB Quantum Kinetic pump onto a Thermaltake core P3 case stock water bracket. This goes between the pump and the stock case bracket to mount securely. This uses the stock EKWB screws to mount the pump to the mount, and X4...
thingiverse
I love my Thermaltake Core P3 case but really wanted to do a dual radiator water loop. Thats why I designed this simple radiato side mount. I created this with a Bykski Radiator in mind but I think (!) that the mounting holes are universal for...
thingiverse
Print four of these to create an AIO mount fitting the Core P3 case. Accomodates any size AIO in a top-mount or side-mount position (don't bottom-mount AIOs!). ... Use a soldering iron to punch mounting holes as appropriate to your AIO model and...
thingiverse
Made a fan bracket to use an extra Noctua NF-A15 in the front of my case. ...The fan didn't fit on the design that Thermaltake has for this so I made my own! ...
prusaprinters
<p>A mount that can hold 360 to 120mm radiators or fans. I needed a mount that could support a 240mm radiator for my GPU and could only find models for 360mm. </p><ul><li>For 360mm radiators just screw in place and then slide onto the poles of...
thingiverse
These are some parts I designed to make my Core X9 custom case build work out how I wanted it. Included is a 3x 3.5" HDD Bracket, 3x 2.5" SSD Bracket and 120-140mm Pump mount adaptor all designed around running 3x 140mm fans in the bottom left side...
thingiverse
this is a cable passthrough cover for the thermaltake P3 computer case. Used it to cover hole for SSD drives. ... No special printing instructions