thin filament 3d models
215132 3d models found related to thin filament.cults3d
X2 Artillery thin filament holder one long and one short model to choose from Gambadino creation
thingiverse
This is a remix of the Maker Select Filament Guide by bwinterton. ...I applied the holes that zanechua put in the larger Filament Guide to the smaller filament guide. ...I buffed up the design in a few places too.
thingiverse
Remix of a filament guide for the CR10, changed to accept an M6 or M9 (M10? the big ones) bowden coupling. Shaved a bit off the top and added a thin cap as to make the whole thing a few mm thinner. This means you keep the full 400mm height of the...
thingiverse
This one fits to original CR-6 SE bracket with the nut in the end (I personally using two nuts). ...This one fits for 18 mm spool
thingiverse
Hi everyone ! ...this is a thin enclosure for the cheap chinese DS0138 oscilloscope. No screws or glue are needed. ...Good printing !
thingiverse
This filament spool holder. It needs four 608Z (8x22x7 mm) bearings. It is just a combination of parts from an original holder (https://www.thingiverse.com/thing:2221639) and it remix (https://www.thingiverse.com/thing:2267430). ... As result it is...
prusaprinters
Female coupler can be swapped for standard M8 nut.For variants Standard 1.75 mm and Standard 2.85 mm you will just need to put filament through.For variant 1.75mm with PTFE insert you will need to insert PTFE tube with length of your liking.Can be...
thingiverse
the cylinder is hollow and the backing plate has been created to save printing time and filament. It has a small lip on the top to prevent the spool from falling off it if gets knocked but shouldn't need supports to print. The word filament is...
thingiverse
Robert Mauser Spooler For Formfutura refill Filament (thin version 2mm) thiner spooler to use less filament and less time to print than the original version
thingiverse
I liked Airtripper's Pocket Filament Reel Rollers, but don't wanted to use four bearings per part. So I made a shortened version of his design. You need one of the original files and one of the shorter ones from me to make a thin version of the...
thingiverse
This one is stretched-and-compressed to fit filament rolls that are too thin and has too large a diameter (roughly 20cm) to fit the original directly. EDIT: It turns out the thickness of these kinds of rolls differs too. Why am I surprised? ...
thingiverse
This is a remix of "Small spool" by tamel55 I shortened the axle so that the spool width was much narrower
thingiverse
All I did was make fipsthedog's filament holder thinner so that my Amz3d filament spool would fit.
thingiverse
I made this clip specifically for the Hongdak PLA 1.75mm spool, which happens to have a thinner wall; to be exact, the clip should fit snug on any filament spool with a wall thickness around 3mm. It was also designed to be printed in PLA, so I'm not...
thingiverse
... Collection: 3. ...Short and long spool holders https://www.thingiverse.com/thing:2067538 You can check it in my video: Better filament holder and filament guide for Prusa i3 MK2 or MK3 / Lepší držiak a vodič filamentu https://youtu.be/q4RPXb2JRJg
prusaprinters
Short and long spool holders https://www.thingiverse.com/thing:2067538 You can check it in my video: Better filament holder and filament guide for Prusa i3 MK2 or MK3 / Lepší držiak a vodič filamentu Print instructionsCategory: 3D Printer Parts...
thingiverse
Customized version of https://www.thingiverse.com/thing:3497066 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3497066
thingiverse
Customized version of https://www.thingiverse.com/thing:2948405 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2948405
thingiverse
Customized version of https://www.thingiverse.com/thing:3181075 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3181075
thingiverse
Customized version of https://www.thingiverse.com/thing:2187167 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2187167