thingiverse ender 3 raspberry pi 3d models

I remixed the original Raspberry Pi 3b case backplate to fit acrylic cases. I added cut-away supports at the Micro SD card opening for a more secure print. This modification allows the case to be printed upright, resulting in a much better finish...

The pi works via the original 24V power supply of the ender to which I added a voltage converter LM2596S set to 5.1V, I do not go through the USB port to power it but through the GPIO ports (as on the vorons). I printed 4 frame_extension to extend...

SummaryI was previously using Sobaldrick's https://www.thingiverse.com/thing:3191174 but upgraded to a Pi 4. Since I couldn't find one that worked for my as well as his design, I mixed up my own. I got the measurements for the front and side holes...

Just took the nice 4040 rail design and enlarged it to fit under my pi 4 on my ender 3 v2. I left the plate full to fit multiple cases but for the canakit case, it's really easy to mark the holes through the bottom plate of the case to get a good...

PLEASE NOTE I HAVE UPDATED THE DESIGN SINCE TO FIX A MISTAKE, DOUBLE CHECK TO MAKE SURE REDOWNLOAD THE FILE I have designed a mount for an existing Raspberry Pi case by ender1968 (https://www.thingiverse.com/thing:3256773 you will need to print this...

To install the pi angle the usb and ethernet ports in, just past the front, then push down on the long side opposite the power and HDMI, then push down the side that had the power and USB and it should snap into place 3. Attach your pi cam cable and...

I made this to power my Raspberry Pi using a conventional USB cable. Just makes life easier. Can even charge your phone from your printer if the printer uses your only power outlet. I used the following USB PSU that is 12v/24v, so I've connected...

I made this to power my Raspberry Pi using a conventional USB cable. Just makes life easier. Can even charge your phone from your printer if the printer uses your only power outlet. I used the following USB PSU that is 12v/24v, so I've connected...

As for the hot bed of my Ender 3 Pro, I suppose it will also work for the standard one.\r\nThe arm has a hole where you can place a support for a Raspberry Pi camera (Rev. 1.3).\r\nThere are two possibilities: a small fixed support and one with an...

Remix : - Less material - Upper camera - Ribbon exit from bottom Works for Ender 3 and Pro

Remix : - Less material - Upper camera - Ribbon exit from bottom Works for Ender 3 and Pro

This bracket is for Creality Ender 3 pro with belt tensioner for y axis

remix of https://www.thingiverse.com/thing:3324678 and https://www.thingiverse.com/thing:3526139 I liked the case with no screws or clips, but wanted the rail to put it on my Ender 3 so took that from the other source

I added a plate which connects to a raspberry pi IR camera via four M2 screws and nuts. The backplate connects to the arm with a single M3 screw and nut, which allows the camera angle to be adjusted. ...I also shortened the rail attachment as my build...

Raspberry Pi 4B Gehäuse zur Befestigung an der Aufnahme des Bildschirms. Der Bildschirm wird oben auf das RPi Gehäuse gesetzt.Ich habe zum Verschrauben Einschmelzbuchsen in den Größen M2, M2.5 und M3 genutzt.Der Bildschirm sitzt recht stramm auf dem...

Simple mount for a Raspberry Pi Camera off of the X-Axis where the belt tensioner is located. ...Has simple "tabs" to hold the cable in place.Included Step and Parasolid files for remixing as you see fit.[EDIT]Added a smaller mount that sticks out from...

... give a firm push onto the rails when mounting. The final feature is the Raspberry Pi logo on embossed into the lid. ... I hope this is helpful, and please let me know in the comments if there are any modifications that you think would be useful.

The pulley cover, however, may not be compatible with all versions of the Ender 3 due to design differences in earlier models, particularly those featuring a distinct style. A camera holder designed specifically for the pi camera version 2.1 is also...

The attachment point to the printer is from the “Ender 3 S1 Holder for Modular Snap Together Rapsberry Pi 2B/3B/3B+/4 Case” by danielvolz, with the mount hole locations from grabcad. In theory this mount should also work with other manufactures of...

... The instructions for wiring and programming the switch are [here](https://howchoo.com/g/mwnlytk3zmm/how-to-add-a-power-button-to-your-raspberry-pi).

Remade the entire design to accommodate a Raspberry Pi 4 and two buck converters, which significantly boosts performance. Additionally, I removed the logo from the cover for a sleeker appearance. ... This build is optimized for a 30mm fan, and I managed...

... on top. I added slits to the bottom for circulation. One improvement that could be made... Instead of screws for the raspberry pi, make the case pieces snap together. ...I don't have screws so the case is open a bit and doesn't look very nice.

As I put a light on back side of the x-axis, I was looking for a Raspberry Pi Cam holder for the backside of the printer. I could not find a easy to print holder, so created a mount for the screws of the power supply. A M4 screw and a nut is...

* A Raspberry Pi would be co-housed within the case to run Octoprint, streamlining the printing process. A notable change was desoldering the MKS's USB-B connector and replacing it with a four-pin header. This allowed for a straightforward...

Pressure-fit the nuts in to the case, then mount the case to the frame of your printer with M4 T-nuts (fits on an Ender 3 v1 at least). Run cables to the monitor, then screw it all together. **Below are notes from the building process:** ...

Inspired by https://www.thingiverse.com/thing:3700643 For one Pi 3A+ and two LM2596 buck converters (5v + 12v) Only the USB ports of the Pi are exposed Hole for a toggle switch (I use it for LEDs) 40mm fan Cable output + fixation for a camera Printed...

Like modern PC cases are done nowadays. Design is based around heat inserts (m3x3x4.2) for all parts but raspberry pi mount - I don't have m2.5 inserts on hand at moment of modelling and assembled, so I have m2.5 self-tapping screw size holes...

The Ender-3 Station by Hesi-Re (https://www.thingiverse.com/thing:3712663) really impresses me. Before starting to print it, I considered adding a small angle under the lip where the original display attaches to minimize supports. For my printer...

Remix of Pi 3+ case to fit Pi4, also reduced thickness of fan mount for shorter screw compatibility and added extrusion for a 12V switch going to my LED strip

So i wanted a bed mount for my raspberry pi camera, so i made this frankenstein-ish thing. Ive added a roofing over the camera hole, it protects from direct light. As i had problems with it exposing my stream and making it really grainy! (Usually...