thread and bobbin 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=46095 Instructions Using the following options: Z1 angle is 0 Y9 angle is 0 X5 angle is 0 Y5 angle is 0 Y2 angle is set at a precise value of 260 Outside radius reaches an impressive 2.5 X7...

so please follow and keep your eye on my updates !!cheers Below are some of the model had been release by me ,pls check them out! ... Espeon FREE https://cults3d.com/en/3d-model/game/free-espeon-pokemon-figurine-3d-print-model baby-charmanderV2...

This 3D model was originally created with Sketchup 13 and then converted to all other 3D formats. Native format is .skp 3dsmax scene is 3ds Max 2016 version, rendered with Vray 3.00 Thank you so much AirbusA330 for helping me on out on this project!

Here are the 3D printers and related products mentioned in the text: 1. **1000$-2000$ 3D Printers** * eBay:...

I found it pretty safe to use the soldering iron to “drill” these holes since some of them are prone to crack the plexiglas at the edge. This is a housing for the new Two Trees SK1.The front door and the lid are detachable.I am going to use some kind...

Solar panel manufacturing alternative sources of electrical energy environmental protection EV electric vehicles EV charging networks electric vehicle networks future electric transport engineering and manufacturing of electric vehicles system of...

This mount also provides means of attaching two 5x7cm daughter boards at the back, cable management for the extruder, heated bed and misc wiring at the bottom, it supports a fan bank with up to 3x 40mm fans.Manual with dimensions for SKR 1.4 Turbo...

By default grid spacing is 0.5 inch in X- direction and Y direction. Ø F8 : Ortho button on/off. Ø F9 : Snap button on/off If snap button is on mode from status bar than cursor will be Jump on the graphic one...

#Add-on Parts 1 - Turbo Accessories add-ons : https://www.thingiverse.com/thing:4633524 2 - Coiling Backing Plate Cover remix : https://www.thingiverse.com/thing:4650185 3 - Timing Cover Gasket add-on : https://www.thingiverse.com/thing:4655883 4 -...

MP1584 or LM2596 or another step down system to power the led in 12 V https://tinyurl.com/yd32xsph mini switch https://tinyurl.com/ycxnb9xy Tnut M3 to handle the mini switch on the frame https://tinyurl.com/yb557um8 Cut the led bar to the right size...

My goal is to create multi-color models that are easy and quick to print. Feel free to follow me, if you want to be informed about when new models are released! <a...

Otherwise You can print "Pipe_half" and glue 2 of them to have 1 entire pipe. You can tighten the M8 screws in the shaft crushing a little bit the end of shaft. ...Consider that it must not withstand strong pressure</p> <p>For dry box, I used too:</p>...

Besides that it only works with 2.5mm backplates, so if you have a ≥3mm plate write in the comments what you need or modify the included .step-files by yourself.I got all the basic models from here: https://github.com/VoronDesign/Voron-0You will need...

It appears you've shared a lengthy document containing information about the settings and parameters used in creating a specific image or scene for the 3D modeling software Corona. I'll do my best to provide a structured answer. ### 1. **Текстуры...

My goal is to create multi-color models that are easy and quick to print. Feel free to follow me, if you want to be informed about when new models are released! <a...

Hi I've just printed some colour samples for my colour fan for my clients, which I'd like to share with you. You can use the openscad file to subtract your own names from the "Farbmuster_LEER.stl" and create your own color patterns with the...

The prototype was not intended for publication.To build it, I relied on personal photos and pictures taken from railway magazines. Let's not forget model railroad catalogs. My attention was focused on a reference offered by BUSCH, from whose catalog...

DELTA PIPE PRINTER (DPP) Please see the DELTA PIPE PRINTER STEP 1 TOP FRAME for more references and instructions http://www.thingiverse.com/thing:1344167 They are no file to download, the configuration.scad is needed to be able to upload this step. I...

My goal is to create multi-color models that are easy and quick to print. Feel free to follow me, if you want to be informed about when new models are released! <a...

the middle sized one im printing right now so im not sure what it is going to do just yet but im pretty sure its going to be fine as far as tolerances but i worry it will do the same as the smaller one an not actually latch to hold its self close,...

This pusher comes in two mounting configurations: one is side mount and the other is flat mount which is parallel with the face of the motor. I recommend using the flat mount configuration because it allows you to tighten the MK8 set screw while the...

I have a lot of gardening weed barrier stuff left over, so that's what I used as 'cloth' to decorate it and give it that ghoulish look, it tears nicely too. I have a hobbyist understanding of electronics, so if you know more then me feel free to...

Should also have enough adjustment to be able to remove the glass and apply a Buildtak surface directly to the aluminum for gaining another 4mm build height. 3 perimeters, 60% infill, .2 layer, PLA</p> <p>FIlament_det_bracket - clip on design that...

I'm reflashing it with an arduino as ISP Configuration Of course you need : #define BLTOUCH Probe offsets (you may have adjust the Z position to you own probe z offset) : //ANET A6 with BLTouch/3D-Touch Front mount // (mount:...

http://www.thingiverse.com/apps/customizer/run?thing_id=1399029 Instructions Using the following options: letter_3_rotation is set at 0 letter_6_rotation stands out with a value of 0 letter_4_y has been adjusted to 4 letter_3_y takes up no space,...

If your print bed can't handle the full length dividers, simply print the two shorter ones and combine them as needed. By joining these six objects, you'll be able to create a divider that fits almost any Akro-Mils cabinet drawer. divider_ext1 is a...

Models optimized for game engines; Multiplication; Advertising and marketing; NFT, metaverses; VR / AR; 3d printing. Features: By combining assets, you can create your own unique land; You can easily change the color of objects - using the UV...

When I discovered I could buy cheap Wireless Qi coils on Amazon—and shortly after Apple released the Airpods with wireless charging case—it unlocked a bunch of design ideas in my head (the voices!!!!!). This design will always have a place in my...

Home server rack using 10" enclosure. You may read more details at DIY Home server rack Notes about services running: Raspberry Pi Home server Raspberry Pi NAS server with OpenMediaVault and Plex | File | QTY | Notes | | --- | --- | --- | |...

Question: What do you get when you combine Bre, a pony, a gangsta, and an octopus? Answer: A Brestacentaurpus. Update: Thanks to Cyrozap for rendering this into an STL for me! <a href="http://www.cyrozap.com">http://www.cyrozap.com</a></p> <p>This is...