thread mount 3d models
407653 3d models found related to thread mount.thingiverse
A two piece mount to hold a QHY5III camera with a threaded hole for a standard camera thread screw (1/4" 20tpi). ... Space for two zip ties to secure the halves of the mount, a piece of tape on the inside of the mount can sure up any looseness in fit.
thingiverse
... to hold a Sony XCD-SXxx0 series camera, modeled to fit an SX910UV but should fit anything with the same housing. ... This leaves four holes on the underside for M3 screws into the camera body and converts it to a single 1/4" 20TPI camera mount thread.
thingiverse
GoPro actually did a clever job with their foldable "things" to mount the camera, but I find it more "universal" with a thread, so I designed this adapter, which replaces the original part on the bottom of the GoPro Hero 8 Black. It bolts on just...
thingiverse
Very basic design for mounting anything with a 1/4" BPS thread to a standard 3D printer stepper motor. I used it to attach some knockoff Loc-Line that I then clipped a raspberry pi camera on the end. The version with the holes in both directions...
thingiverse
A threaded bowden mount for the hot end of a Hictop Prusa i3 3d printer.
thingiverse
This is 17mm thread lens mount/holder for iPhone SE 2020. This holder was created for 1.33x anamorphic lenses from Ulanzi, which are attached using a 17mm thread. The holder was tested with Ulanzi 1.33X Pro 3rd Generation Anamorphic Lens. ...Other...
thingiverse
This is a stubby 1/4-20 thread adapter for the Panavise suction cup camera mount. I designed this so I could install a 1" ball mount and use RAM style attachment arms. It will accept a standard 1/4-20 nut or bolt in the hex cavity. ... Also fits the...
thingiverse
... a JAI CM-140 GE series camera, modeled to fit a CM-140 GE-UV but should fit anything with the same housing. ...This leaves four holes on the underside for M3 screws into the camera body and converts it to a single 1/4" 20TPI camera mount thread. ...
pinshape
Summary Enables the use of M39 LTM/Leica Screw Mount lenses on MFT cameras.
thingiverse
Enables the use of M39 LTM/Leica Screw Mount lenses on MFT cameras.
thingiverse
Remixed part, the difference is I have increased the base from 1.3mm to 3mm as I found it a bit fragile on the original version.
thingiverse
Had a vintage small camera tripod sitting around and thought it would be great to mount my webcam on it. ... Took darkspoon's mount and just used the part that holds the C525 webcam and added a 1/4-20 threaded hole. enjoy! ...
prusaprinters
Finally a decent XT60 mount, use a 1-1/8" (30mm) hole saw or step bit to mount.Press fit a male end xt60 into the body, no additional hardware or adhesive needed. ...The body and nut can be printed with PLA/ABS/PETG, the lid needs to be in TPU for...
cults3d
Finally a decent XT60 mount, use a 1-1/8" (30mm) hole saw or step bit to mount. Press fit a male end xt60 into the body, no additional hardware or adhesive needed. ...The body and nut can be printed with PLA/ABS/PETG, the lid needs to be in TPU for...
thingiverse
This is a hotend mount for the Cetus 3d mk 2 combined with an e3d v6 hotend with threaded mount. IT IS NOT TESTED. But I will do that in the near future. You will also need an external fan and a very light 30mm hose. ... (Print settings is what I...
thingiverse
The standard e3d fan duct doesn't work very well with the threaded mount version of the heatsink because the fan can come into contact with either the mounting surface (effector, etc) or the heater block. ...This version of the fan does not extend above...
thingiverse
Leveraged the threaded mount and knob from https://www.thingiverse.com/thing:3147899, and a customized ball mount for my IPEVO Point 2 View document camera. Camera mount point remixed from: https://www.thingiverse.com/thing:2421879 Because the...
thingiverse
A simple mount for a FLIR Boson thermal camera core to adapt it to a standard 1/4" 20TPI threaded camera mount. This was designed for the core with shutter and lens assembly - the unit tested on was a 50 degree HFoV lens, but since the mount...
thingiverse
Ender 3/5/whatever frame mounted webcam mount, will fit on anything with a square tube frame < 25mm wide Uses 1/4-20 tripod threads Hardware used: [1] 1/4-20x3/8" screw [1] 1/4-20x3/4" screw [1] 1/4-20 nut
thingiverse
It has a GoPro mount on top of a simple threaded "block" to screw onto the tripod mount threads. This was my first real practical 3D CAD design and I designed it with a M16-0.7-8.5 thread in Fusion360. Pretty specific design that I don't think...
thingiverse
I added a 1/4-20 threaded hole and removed the wall mounting holes. I also made some dimensional changes so it fits well and doesn't need supports. I'm using this in combination with a printed clamp mount for our bassinet. You could mount a tripod or...
thingiverse
I was looking for a way to mount a dremel 4000 onto solid surfaces as simply as possible and found this mounting solution for a cnc attachment. I've removed the angled tabs and the rounded back, and I've added a flat base with pretty flexible holes...
thingiverse
Thread Screw Mount Adapter - http://ali.pub/4kpohn You can also make the screw if there is a tool, or just buy a ready-made screw, cut off the hat and you get the same thing. UNC 1/4 20 - <a href="http://ali.pub/4kpo3g"...
youmagine
I wanted to mount my GoPro to the bike with a quick release adapter so I just made a socket for a 1/4"-20 UNC nut in the sole.
thingiverse
This takes @ModelStation's excellent PCB Vise and @hesperaux's more printable jaw shapes, and adds an industry-standard 1/4"-20 threaded mount. My heavy camera ballhead is not going to move around on my desk or droop like those spindly little...
prusaprinters
This takes @ModelStation's excellent PCB Vise and @hesperaux's more printable jaw shapes, and adds an industry-standard 1/4"-20 threaded mount. My heavy camera ballhead is not going to move around on my desk or droop like those spindly little...
thingiverse
I had a couple of XLR microphones that came with a 5/8 threaded mount. ...Whipped this up for a desktop stand.
thingiverse
After losing a body clip I decided to make a threaded mount that would eliminate the need for clips. ...I printed this in CF nylon and it had been indestructible so far.