throwie 3d models
51 3d models found related to throwie.thingiverse
A basic throwie with 4 spaces for magnets. A space for a battery was not included as it is held in place by the magnets. ...(Which are glued into place) The copper tape showed in the images proved to not be needed, but I didn't want to take it off.
thingiverse
Made in tinkercad. Circuit is a battery, LED, and magnet. ...Shaped so light can been seen through the sides and the top.
thingiverse
I used Thing-o-matics makerbot to make a cube and a lid. Inside the cube I had an led, battery and a switch. I soldered one lead of the switch to the cathode and then a wire to the other lead of the switch which rested on they positive side of the...
thingiverse
It is a cylinder and a cap that was built on Blender and printed out on a Thing-O-Matic. ... It contains an LED which I soldered to a reed switch and connected to a coin cell battery, so that when you put a magnet near the reed switch the LED it lights...
thingiverse
A 3D-printed improvement on the classic Throwie. Glue on a magnet, add a battery (CR2025), and insert a diffused LED. ...Some colors will glow for months!
thingiverse
... easier to pull the coincell out with your fingers. No power switch, in true throwie fashion, if you want it turned off pull it apart. Remember the usual throwie rules of take care of spent batteries and it is probably best to not leave unattended.
thingiverse
Just in time for Halloween is this skull throwie. I used a quick and dirty approach to prep this model from 3dcool.net for printing using blender. you will most likely want to tweak the model for higher quality since this was intended as a test. Feed...
cults3d
[Or longer with a newer battery ;-) ] If you don't have candles but you do have stuff for throwies here is a slightly better way to light the room. I also thought it would be useful for lighting decorations and projects. It is the same size diameter...
thingiverse
https://youtu.be/mGZuaQzcXH8 3D printed a simple holder for coin cell batteries and make LED throwies that’s re-usable for Slime projects. Just pop in a coin cell and press fit them together. Build an LED throwie kit for your classroom or workshop. ... ...
pinshape
3D printed a simple holder for coin cell batteries and make LED throwies that’s re-usable for Slime projects. Just pop in a coin cell and press fit them together. Build an LED throwie kit for your classroom or workshop. ... Resources & Learn...
cults3d
https://youtu.be/mGZuaQzcXH8 3D printed a simple holder for coin cell batteries and make LED throwies that’s re-usable for Slime projects. Just pop in a coin cell and press fit them together. Build an LED throwie kit for your classroom or workshop.
thingiverse
A fun 8 Bit Skull Throwie. ...Add 2 5mm LED's and a 2032 battery Instructions A fun LED Skull Throwie, Printed on a Replicator 2 with standard print settings. insert 2 5mm LED's and a 2032 battery. snap on the back plate. ...Have fun...
youmagine
3D printed a simple holder for coin cell batteries and make LED throwies thatâs re-usable for Slime projects. Just pop in a coin cell and press fit them together. Build an LED throwie kit for your classroom or workshop. ... Resources & Learn...
youmagine
... The recess also extends 2mm below the deck to make sure the surface it is being subtracted from gets removed.Octo-led is an example of removing the throwie from an existing model, in this case the classic http://www.thingiverse.com/thing:8896
thingiverse
This is a pair of almost identical casings for throwies which fit together in several different ways and allow easy access to the LEDs so that it is easier to replace any dead battery. This was designed in tinkercad and printed using a MakerBot. I...
thingiverse
... is an example foot model cutout I did, which illuminates nicely. http://www.youtube.com/watch?v=AewEMUqiBk8 Instructions Print out, attach throwie or stringlight and go! ...I've included the original model for some custom boolean action.
cults3d
The small magnets used to couple the build platform to the y-axis are hard to find locally, so I created this build platform that uses the magnets that were readily available at the hacker space, throwie magnets!
thingiverse
This is a portable LED lamp, which was printed in two pieces in a makerBot containing a controlled LED with a button battery, so that when the lid is pressed the LED lights. ...Inventoteca
thingiverse
This LED throwie uses a magnetic reed switch to save energy by only turning on the LED once the throwie comes into contact with a magnet stuck to a metal surface. The LED switching circuit consists of a ultra bright LED with the positive lead...
thingiverse
The small magnets used to couple the build platform to the y-axis are hard to find locally, so I created this build platform that uses the magnets that were readily available at the hacker space, throwie magnets! ...
thingiverse
Instructions Drag and drop the shapes in this file into your throwie-frame design to have a perfect set of battery/LED clips every time. This is a file that will allow you to cut perfect clips to hold an LED in place inside an acrylic frame. The...
thingiverse
This is part LED Throwie, part Light Guide, part Lapel Pin, and it makes a great conference promo item! This was inspired by BDG Customs Light Guide on Thingiverse:http://www.thingiverse.com/thing:16230 ThingTankLab.com will use them as a conference...
thingiverse
I got this idea when Daniel Spangler, one of our Make Labs interns, finished building a DIY trebuchet kit at 10PM and wanted to launch stuff with it. He taped LEDs and a coin cell battery onto a tennis ball so that we could see where it would fly in...
cults3d
I got this idea when Daniel Spangler, one of our Make Labs interns, finished building a DIY trebuchet kit at 10PM and wanted to launch stuff with it. He taped LEDs and a coin cell battery onto a tennis ball so that we could see where it would fly in...
cgtrader
... solid fill 2. PumpkinBoolean is the pumpkin with the center hallow and a hole in the bottom for Throwie insertion or string light. 3. ...PumpkinFoot55 is an example foot model cutout I did, which illuminates nicely.youtube.com/watch?v=AewEMUqiBk8
cgtrader
... solid fill 2. PumpkinBoolean is the pumpkin with the center hallow and a hole in the bottom for Throwie insertion or string light. 3. ...PumpkinFoot55 is an example foot model cutout I did, which illuminates nicely.youtube.com/watch?v=AewEMUqiBk8
thingiverse
"Electronic graffiti", it's simply a magnet, LED, and small button battery. You toss them is on some metal surface and they turn on, and last for a few days: https://www.youtube.com/watch?v=AX7jA4NJV8s&feature=youtu.be ...
thingiverse
Case for ESP8266 yellow dev board V2: thin walls for faster printing and hole for power switch 2.80 € ESP8266 board at aliexpress.com RGB multicolor LED SMD LED's for 6x GPIO switche / relay Photoresistor / sensor Temperature / buildin chip sensor 3x...
thingiverse
The Placie Case is for an LED throwie to be put inside. It has a place for the magnet, battery and LED. ...Then you can glue the two pieces together and place it on any metal surface you want!