tie pad 3d models
56795 3d models found related to tie pad.thingiverse
Here is a cable tie pad. Take a piece of tape for mirrors and stick the pad everywhere you want. ...Printed with layer 0.25 Infill 0.2
prusaprinters
So I came up with the idea to design these pads that are elongated along the cable.InstallationIf the available space is really small, and hard to reach with your fingers (like on the backside of a motorbike fairing or in some tight corners of a car)...
thingiverse
Another version of zip tie anchor with screw holes. I often put double sided foam tape on back for fast mounting. Recommend higher resolution, high infill for strength. ...Updated to V2 to add reinforcement for apes like myself who torque on zipties.
thingiverse
Used to mount a zip tie to a wall or board. ...To mount the pad, install a double sided adhesive strip to the back and/or a #6 screw through the center.
thingiverse
Mounting pad suitable for tidying up wires with cable ties. I've made one "tunnel" 1 layer (0.25mm) higher than the other to make bridging easier. Suit 25mm (1") foam tape or glue. Tunnels are 8x2mm. ... Printed 0.25mm layer heigh
thingiverse
the thing can be glued (or with 2 sided adhesive tape) to a surface and act as a stronghold for a cable tie (trough the holes) and nicely fit a bunch of cables close to a surface. The bottom looks rough ans that is on purpose to gain a bigger...
thingiverse
This is a prototype CAD model for a 1" x 1" Cable Tie Mounting Pad.
cgtrader
Galactic lmperie small TIE landing pad for small ships on a base,asteroids,planets,and other important objects in galaxy. That landing pad have a shield generator and fuel system. ... Files max 2012,fbx,obj,3ds,7z
thingiverse
Either glue accessory to the base or import a "clip" and build on it. In this example I mounted an extra trimmer spool to the trimmer body. When line runs out I don't need to go back to shed or garage to get new trim line. Change the length or...
thingiverse
Includes a hole to add a fastener. ...Print Settings Printer: Witbox 2 Rafts: Doesn't Matter ...
pinshape
Summary Thanks to Isolt for the original model! 20x20 mm. A remix to suit my own needs (20 mm wide foam tape). UPDATE Added a version 2 with a thinner roof part to save some (admittedly minuscule) filament, because the thickness didn't seem to...
thingiverse
*Thanks to [Isolt](https://www.thingiverse.com/Isolt/about) for the original model!* 20x20 mm. A remix to suit my own needs (20 mm wide foam tape). ... **UPDATE** Added a version 2 with a thinner roof part to save some (admittedly minuscule)...
thingiverse
Zip tie designed from scartch, just to learn how to use all the software needed to make a 3d printed part.
thingiverse
Hole for screw mounting added on the bottom. ... The top hole is rectangular and can be printed without supports.
thingiverse
Remixed from the famous "Rebel Pilot / Tie Fighter Pilot - Comm Pad" by muckychris. I sliced the Comm Pad in a Base and a Main Part + Details (Buttons) and added a Battery (2x C2032) holder at the inner side of the Pad. The Buttons where...
thingiverse
Can be mounted on any surface with double-sided adhesive tape. ...Different radius to hold different cables. Easily fasten the cables with cable ties.
thingiverse
Simple cable management mounting pad for twist ties or small zip ties. ... 15mm Long 15mm Wide 4mm Height
thingiverse
Rebel Version 2x - But1 - Blue 2x - But2 - White 1x - But3 - Blue 4x - But4 - 3 Blue / 1 Red 1x - But5 - Black Tie Fighter Version 2x - But1 - Red 2x - But2 - Red 1x - But3 - White 4x - But4 - 2 Black / 1 Red / 1 White 1x - But5 - Gray Note: I did...
prusaprinters
I created custom supports that snap away easily after printing. Rebel Version 2x - But1 - Blue 2x - But2 - White 1x - But3 - Blue 4x - But4 - 3 Blue / 1 Red 1x - But5 - Black Tie Fighter Version 2x - But1 - Red 2x - But2 - Red 1x - But3 - White 4x -...
cults3d
I started with AprilStorm's Comm Pad and reworked it just a bit. I separated the buttons so it can be printed for the the dark or light side of the force. I compared this to the current resin version that 501st peeps are using and figure this is an...
pinshape
I started with AprilStorm's Comm Pad and reworked it just a bit. I separated the buttons so it can be printed for the the dark or light side of the force. I compared this to the current resin version that 501st peeps are using and figure this is an...
thingiverse
This is a Wall Pad for zip ties ( to hold something to a wall with a ziptie) Use special wall glue for this in austria its named (kleben statt bohren) glue instead of drilling. ...or use similar products.
prusaprinters
This is a Wall Pad for zip ties ( to hold something to a wall with a ziptie) Use special wall glue for this in austria its named (kleben statt bohren) glue instead of drilling. ...or use similar products.</p>
thingiverse
Updates to muckychris 1 piece Comm Pad to be 501st CRL compliant. Added rivets to the squares and made flat one of them. White Split button has been made Flat. ... This is a remix from https://www.thingiverse.com/thing:150129
thingiverse
Updates to muckychris 2 piece Comm Pad to be 501st CRL compliant. Added rivets to the squares and made flat one of them. White Split button has been made Flat. ... This is a remix from https://www.thingiverse.com/thing:1650986
thingiverse
Not really a remix, but made a cable tie bracket to go with it so you can tie up all your cables under the pad. ...
thingiverse
I made this clips to help me install some 8mm LED strips on an angle and tie them onto sticky pads. ... I used 8mm LED strip 25mm sticky pads 2.5mm cable ties