tin whistle key of a 3d models
3661936 3d models found related to tin whistle key of a.cults3d
I designed this Tin Whistle! Please let me know what you guys think and if you think of any improvements that could be made make sure to comment. Audio Sample: https://sndup.net/3hqb It prints in 3 parts, orient them like in the picture. No...
thingiverse
I designed this Tin Whistle! Please let me know what you guys think and if you think of any improvements that could be made make sure to comment. Audio Sample: https://sndup.net/3hqb It prints in 3 parts, orient them like in the picture. No...
thingiverse
... may be required for it to fit good and I used some bees wax on the joints. An exacto knife will clean up the inside of the mouth piece. If you have any stringing in the wind channel of the mouth piece, a small file does a good job cleaning that out.
thingiverse
I had to cut a little out of the window with a knife to get a good sound, but it plays pretty close to in tune. I printed with supports, which required cleaning out the inside (I used a large drill bit). I don't think it actually needs supports,...
sketchfab
An item of an elongated shape made of a tubular bird bone. On its surface there are thin parallel notches. ...Material: tubular bone Size: 48x27 mm Region: Transbaikalia Archaeological culture: Early stage of Upper Paleolithic Site: Kamenka Storage...
thingiverse
Unified body parts A and B from the model: Tin Whistle / Penny Whistle in the key of D by iceman1979
thingiverse
Thanks very much to thetunebot for sharing his excellent Tin Whistle design at: https://www.thingiverse.com/thing:4943965 I experimented with thetunebot's original .stl to streamline the tube in the middle where the writing is as well as at the end.
thingiverse
Thumb ring/rest for a tin whistle/penny whistle. ... Definitely fits a Walton C-scale.
thingiverse
Tin whistle for myselves. ...In head of whistle need cut holes. ...For best connect I used boiled water.
cults3d
This is a simple stand for holding one tin whistle. Tested with Clarke "The Original Tin Whistle" and Clarke "Sweetone Tin Whistle". Should work with any print settings, since it's just a stick on a cylinder. Blender source file attached for...
thingiverse
This is a simple stand for holding one tin whistle. Tested with Clarke "The Original Tin Whistle" and Clarke "Sweetone Tin Whistle". Should work with any print settings, since it's just a stick on a cylinder. Blender source file attached for...
thingiverse
Thumbrest designed to snap on to a tin whistle. You can customize it to the size of your whistle's barrel, and it works with tapered barrels. The .stl file here fits my Clarke D whistles. This is marked as a work in progress because I intend to go...
thingiverse
These are 2 tin whistle holder I designed for my irish flutes. One you can mount at a wall for example. ...The other could be used as a hanger for trousers or note stands.
prusaprinters
... a few percent if it's to tight or too loose for you. ...It's just a friction fit. I find it's best to manually put the seam on one side so it doesn't end up spiratic. 0.3 layer No Support needed print separately for best results.
thingiverse
If you want, you can put in top and bottom part a bit foam (with double adhesive tape) to protect the whistle better. In pictures is my Waltons Mellow, fits perfect. Smaller should also. Longer are not an problem, but thicker, maybe. You can...
prusaprinters
Other whistles that taper, like the Clarke, are a looser fit, but they still hold.** I believe non-D whistles, such as a Bb, etc., may be slightly larger in diameter--up to 17mm?--so they won't fit. Perhaps I'll update this model if (when?) I get...
grabcad
This is an Irish whistle (aka penny whistle) that can hopefully be 3D printed and fully functional. ... Different materials will have different sounds. Eventually someone can print their very own full set of whistles!
thingiverse
Customized version of http://www.thingiverse.com/thing:46825 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=46825 Instructions Using the following options: laenge =...
thingiverse
Customized version of http://www.thingiverse.com/thing:46825 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=46825 Instructions Using the following options: laenge =...
thingiverse
Customized version of http://www.thingiverse.com/thing:46825 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=46825 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:46825 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=46825 Instructions Using the following options: textshow...
thingiverse
Customized version of http://www.thingiverse.com/thing:46825 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=46825 Instructions Using the following options: hoehe =...
thingiverse
Customized version of http://www.thingiverse.com/thing:46825 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=46825 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:46825 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=46825 Instructions Using the following options: textshow...
sketchfab
Whistle In The Form Of A Bird (200 BCE - 500 CE) Mexico, Colima Slip-painted ceramic 4 7/8 × 4 1/4 × 2 5/8 in. (12.38 × 10.8 × 6.67 cm) Gift of Dr. and Mrs. ...Louis Feldman View more objects from Colima, Mexico in LACMA’s collection!
prusaprinters
My dad plays the irish Tin Whistle in a folk band, and his mouthpiece died a while ago, so I offered to print new ones for him… And ended up reading a ton of books & scientific papers on the acoustics of flutes, so there are 3 variations here,...
thingiverse
Customized version of https://www.thingiverse.com/thing:738778 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=738778