tiny modelling

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

My goals for this project were to model everything with the least amount of material waste (support material) needed and that everything is easibly printable. What you need to print: 1x air.stl, 15%-20% infill, support on built plate only (I suggest...

Every detail has been painstakingly worked by our artists, who have also designed the tiles to ensure repetition of patterns are minimized as much as possible on each miniature/model in the INSTADUNGEON™ series. LET EACH TILE'S PHYSICALITY IMPACT...

Particularly VERY IMPORTANT you need to change the setting from the default Negative Image to Positive Image. Adjust the Model Settings as I have shown in this Thing images. The Size (width) MUST be 150mm. Also I suggest reducing the thinnest layer...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

  Walmart also has a good deal on a 4 Pack of the same filters HERE.The fan is a Black & Decker 9in Mini Box Fan, Model BFB09W.CostAt the time of writing this the total cost is the same for each of the 3 versions as the different sized filters are...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

 I use a cheap little fingernail drill to do most of my sanding as a dremel can somtimes be overkill and it comes with a ton of little heads it'll take me years to use up.https://www.amazon.com/dp/B07T8H3531?ref=ppx_pop_mob_ap_shareThe final...

I changed the position of the threaded inserts and added additional to replace the hex nuts. Modified the cable paths and tie wrap holes for easier printing, and thickened up some sections to print better. Modified how the front and rear clamp...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

In my 4 months of using it non-stop it has never come loose or moved, the force needed to take it off the rail is a bit more than the force needed to make the motor skip steps so something would have to go CATASTROFICALLY wrong to make the tool...

It has been argued that for the N2+ model with a print that could fill the entire 2 foot tall bed, these springs would compress and the object would then miss layers and ruin the print. If I were worried about printing that tall with that high a...

This meant adding three holes for screws, and I also added flanges on the bottom in an attempt to mount the fan shroud I modified for my model cooling fan shroud. I left the sensor port alone for now - I may or may not try using the cooling fan...

Attention, there is V2 as when I was designing this I didn't think about some stuff so I added them, but I didn't print this updated model. I'm only unsure about the switch if the top cover will fit as I think it should.</p> <p>Features:<br/> ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Mountains in brown, oceans in blue, you get the idea! This was a couple weeks worth of modeling exercise, and I had a lot of fun. I hope some of you manage to have some fun with it as well!</p> <p>I only had gray PLA on hand to print the test tiles...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Here is a link to the controller - Link**: https://amzn.to/3NtTmzI As motors I fly the T-Motor F15 with 6000KV 2-3S Link** - https://amzn.to/444i6FV Unfortunately this is a discontinued model the motors should not be below the height of the F15,...

In order to stay within bed size, put your skirt 0mm to the model. Once printed, remove the support material and clean up with sandpaper. Step 2: Print 2 Simple Metal Spool axle holders, same Splic3r settings as above. You can print both of them on...

Subscribe Now! A very good model from LSMiniatures. Remixed to support free to do timelapse. https://www.youtube.com/watch?v=3NDJFnoX_3g <a href="https://www.youtube.com/watch?v=3NDJFnoX_3g"><img...

Well first, customization (as in the mag cozys), cost (may be cheaper if you have a 3d printer already, though i hope you didn't buy a 3d printer just to print mags), and finally, they actually are closer to katanas than talons, meaning that they...

I need thosethree measurements from that photo: Front standoff spacing, back standoff spacing, and front-to-back spacing.I've already helped several people from across the globe and I've been updating this document with the new models as I go.Post...

... can get rather hot. PLA may work; I'm not sure. Use a minimum of: 3 perimeters 20% infill 4 top and bottom layers The model for the base plate isn't oriented correctly-- print it flat with the side labeled "TOP" upwards. Category: 3D Printer Parts

Star Wars 3D Print File - Admiral AckbarThis model is designed to fit our 3D Printable BodyJoin our Patreon - Limited spaces left. (only $3 a month)https://www.Patreon.com/3dxfiles Action Figure Head sculpt 1:6th scale - Darth Maul. It can be...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Using the paint supports tool in PrusaSlicer, put supports around the square cutout that you can see by looking through the bottom of the model. Look at the image below for reference.</p><figure class="image image-style-align-center image_resized"...

... mount and two each side for accessory mounts. I used one on the right for strain relief for E3D wires, 2 on left for fan mount. 4 on side fan, only two are used depending on fan model. ...2 on cable chain attachment to attach it to extruder mount.