tinyhawk camera mount 3d models

A Lollipop Mount for the Tinyhawk Freestyle 2 that just slides on the back 2 mount bars. It can be mounted while the antenna is already soldered to the VTX. PLA/TPU (TPU for flex) For PLA is has to be printed exactly like the Picture from Cura,...

it weight less than 2g. but like everybody, we do not like it because we can not simply install in our current drone since it use weird fittings.also Tinyhawk Frestyle is not the best frame for modification. i can see a lot of people having trouble...

I'm just trying to repurposed the motors for a dead emax tinyhawk freestyle

I desperately needed a firefly mount for my tinyhawk freestyle so I went ahead and created one - it was definitely a challenge! 5,25 and 45 degree mounts, and a strap to help keep the plug out of the props were all part of the design. Flexible...

After i installed an runcam thumb on my tinyhawk i wasn't able to moun the battery so i designed this and its better balanced now

replaces stock camera mount and holds insta360 go upright behind it for fpv mode video

This camera mount is specifically designed for the Insta360 Go HD camera. https://www.insta360.com/sal/go?insrc=INRO7M1 The primary intention of this mount is to be installed under the Emax Tinyhaw2 Race, utilizing the lipo strap. ...This particular...

... ventilation in the back (also incase your camera gets stuck). Secures with a rubber band. You should add a ballast to the back for increased performance but I can barely tell the camera is there in flight. ...Print upright with tree supports (cura).

Removed the external vtx antenna mount.

... the camera yoke's robustness. Super Glue these parts together and secure them with a thin layer of cotton to boost overall strength. Modify the frame by carefully removing a small portion around the camera opening to simplify installation.

... to the exact same height as their counterparts in the original print job. To ensure seamless connectivity, you will need to lengthen your wires for the camera connector. ...Perfectly calibrated camera angle demands precise adjustment to 25 degrees.

this mount is for when you need to change the angle of the insta360go

XT30 housing (use CA to secure) and antenna mount. Use a cable tie and brace the antenna against it with heat shrink. ...Heat shrink not shown in photo.

You can use different 1S 250mah or 260mah batteries with this mount by making a simple " Y " PH 2.0 connector harness connected in parallel as shown in the pictures. To print, use flexible filament and set your infill to 50%. Enjoy! Let me know how...

mount for the Runcam Thumb on the EMAX Tinyhawk II

Emax Tinyhawk II Freestyle r-xsr (xsr, xm, xm+) antenna mount to back

Just my design of a Insta360 Go mount for the Tinyhawk Freestyle 2

This is a custom mount designed to securely attach an Insta360 camera to a Tinyhawk II Freestyle drone. It's specifically engineered for the wider frame of the TH Freestyle 2, ensuring a precise fit and optimal performance. ...The mount can be easily...

Per request. ...Here is a version of the Freestyle 1 mount with correct spacing to fit the Tinyhawk Freestyle 2.

An Overhauled Camera Mount for the Runcam Nano V2 Unveiled - A Custom Fit for the Original Tinyhawk Freestyle Model. Designed with precision to accommodate the stock screws without requiring any drilling, this enhanced mount is tailored to meet the...

This allows you to mount an Insta360 Go 2 on your Tinyhawk Freestyle. It reuses the factory screws. Print it in a flexible material like TPU, or you'll get jello. There are cutouts for magnets, but I don't recommend using them. They'll pop loose...

I was fighting with jello on my Insta360 Go2 on TinyHawk Freestyle II, designed and tested many many mounts printed with a lots of different materials, that was very long, time and resources consuming process, but finally i think i got it :-).

made a simple elrs ep1/2 rx mount for the tinyhawk series. not sure if itll work well for tinyhawk 2 freestyle frames/build or any tinyhawk models that use a different FC than the fc series of the OG tinyhawk. printed in tpu with supports, make sure...

This is my mount to put an insta360 onto a Tinyhawk II Freestyle. It has the correct spacing for the wider frame of The TH Freestyle 2. ... It can be printed from TPU without support if you have your printer dialed in.

This is an Insta360Go case and adjustable mount for the TinyHawk Freestyle 2 from eMax. there are 2 versions of the mount, one plain and one with BRUS Special Request for: BrusCalus Send me a message if you need this altered or something different...

Allows direct mounting for dual rear rx antenna support, TBS triumph pro antenna support, mount for rushfpv tank tiny vtx. UPDATE 23//01//21: I've now stopped working with the rx antennas version as i found the rx/vtx antennas to be causing...

Hello, this is a AIO Board (Whoop Size 25x25mm) holder for the Tinyhawk 2 Freestyle Frame and a holder for a Full Size Cam (19x19mm). Happy printing and have Fun. ...;-)

I wanted a version to mount to the top of the quad (I'm not using a camera mount), so I included two cutouts to make room for the stock camera frame. ...I also modified it for a different printing orientation and reinforced it in one direction for...

This is a camera mount, Non TPU may cause Jello or Vibrations - SWAP THE PINS ON THE RUNCAMSPLIT - the runcam splits plug fits, but the cables are out of order from what the board wants, check the pins on the runcam 3 and you will find what order...

... the design of the base where the mount fits easily. I leave 7 files: 1- Base a- version 15° b- version 15° without lipo holder c- version 25° d- version 25° without lipo holder 2- Insta360go Mount 3- Insta360go v2 Mount 4- base with bumpers