tinyhawk freestyle 2 3d models
948286 3d models found related to tinyhawk freestyle 2.
thingiverse
Top plate for emax tinyhawk freestyle 2 with a cut out for the usb on a f4 1s 12a aio fc. This also has a holder for an xt30 plug and an antenna. ... 2mm screws thread into the pla holes on the standoffs and holds it on fine saving some weight.
thingiverse
Remixed (https://www.thingiverse.com/thing:4117499) to fit the Tinyhawk Freestyle 2. The hole in the back is big enough to fit 2 1s connectors through. If you want a version without the text just let me know. Printed this in PLA without...
thingiverse
Bumper for Emax Tinyhawk 2 Freestyle to protects the screws on the bottom. Printed and tested with 0.1 resolution in petg. Adds around 3g to the quad. ... This model fits for me tight, but maybe you have to scale it a little bit smaller in case...
thingiverse
This is an adapter I made to mount a happy model f4 1s 12a aio fc on the tinyhawk freestyle 2 frame. ... This should work for any fc with 25.5mm mounting holes.
thingiverse
This is a prop guard for Tinyhawk Freestyle 2 that don't need you to remove the motors/screws. I'm still improving the protection area without increasing the weight so much. Mirror print for opposite side. Print on TPU. ... facebook.com/FPV3DPrints...
thingiverse
Use this mount to secure your Insta360Go to your tinyhawk freestyle 2. I made this when I almost lost my Insta360 in the very first crash due to a fragile mount. I printed mine with TPU. You don't have to use any supports if your printer is...
thingiverse
Detachable whoop for Tinyhawk Freestyle 2, may fit first version, but can't check. You just put it over the frame and secure with the same strap as the battery. It is not a full whoop, it is still possible to put fingers into props, but you can...
thingiverse
Tinyhawk freestyle antenna mount. protects against accidental damage that can occur. I printed it in TPU. ...No add-ons are required.
thingiverse
TinyHawk Freestyle II Bottom Plate Frame 3 versions. Close to original frame. 2mm arms supported frame. 2mm thicker than first one with all screws are recessed. "NEW added Top plate .STL If your printer can print dimensions correctly this...
thingiverse
... from a design i found on this site. also included is a mount for the insta 360 go 2. together with the clipon propguards(also found here on thingyverse) it makes a nice way to fly safely around people and indoors while carrying the insta go 360 2
thingiverse
a simple mount for an insta 360 go 2 on the tinyhawk freestyle 2
thingiverse
Just my design of a Insta360 Go mount for the Tinyhawk Freestyle 2
thingiverse
Per request. ...Here is a version of the Freestyle 1 mount with correct spacing to fit the Tinyhawk Freestyle 2.
thingiverse
One piece mount for the Insta360 Go 2. No jello, with good ventilation in the back (also incase your camera gets stuck). Secures with a rubber band. You should add a ballast to the back for increased performance but I can barely tell the camera is...
thingiverse
This is an Insta360Go case and adjustable mount for the TinyHawk Freestyle 2 from eMax. there are 2 versions of the mount, one plain and one with BRUS Special Request for: BrusCalus Send me a message if you need this altered or something different...
thingiverse
Rear antenna array for the Emax Tinyhawk freestyle 2. Allows direct mounting for dual rear rx antenna support, TBS triumph pro antenna support, mount for rushfpv tank tiny vtx. UPDATE 23//01//21: I've now stopped working with the rx antennas...
thingiverse
I hope this design will help you to place an xt30 and buzzer in the freestyle 2. ... Leave the part open so people who already have the xt30 don't have a hard time
thingiverse
Propeller guards for the Tinyhwak freestyle 2. I'm using these for indoor flights. Simply Clip on the frame. They slide over the screws. ... Print mirrored for the other arms
thingiverse
... the design of the base where the mount fits easily. I leave 7 files: 1- Base a- version 15° b- version 15° without lipo holder c- version 25° d- version 25° without lipo holder 2- Insta360go Mount 3- Insta360go v2 Mount 4- base with bumpers
thingiverse
this mount is for when you need to change the angle of the insta360go
thingiverse
These are two simple parts to keep the battery (or batteries) from sliding off while strapped down with the velcro strip. It is recommend to print this using a flexible material, like TPU. There are two different versions for the front. ...One...
thingiverse
Linear antenna is a bit too bad for my taste, so I decided to swap it with a circular polarized one. In this case, it's a Speedy Bee RHCP. When flying, the angle positions the antenna free of the batteries. The idea is to fix the it to the TPU...
thingiverse
Camera mount for the EMAX tinyhawk freestyle 2 to fit any 19mm fpv-camera. I designed this especially for the runcam racer 5 but every other 19mm fpv camera should fit as well. The mount replaces the front standoffs, just use the original screws....
thingiverse
Print with tree supports preferably. Print mount in upright orientation. Soft mount with double sided foam tape on the bottom (remove protective backing at personal preference, I did not remove). Top side soft mount is two spacer o-rings. Rig is...
thingiverse
The idea borns because the VTX antenna it's very close to the prop, and with a very little bend it can touch the prop blade. This holder has a "guide" for the VTX antenna that now it's safe, and lock the front part of batteries that with only one...
thingiverse
This is a soft mount that can solve the Jello problem on the Insta360 GO. ... Take a look at the video on my YT channel: https://www.youtube.com/watch?v=GSTVzVCG4JQ&t=18s Need 2x O-rings to complete the assembly.
thingiverse
print with tree support and remove the support with a scalpel remix of https://www.thingiverse.com/thing:4621416