titan aero anet a8 3d models

I support the Titan extruder on the upper right side of my Anet A8. ...I position the motor forward so that the bottom wheel doesn't touch the chassis.

Here are some parts I designed to convert my Anet A8 Plus to use an E3D Titan/V6 Direct Driver Extruder/Hotend, as well as the little part cooler I designed (still needs some work, will update sometime). Also included is an adapter plate to mount a...

I've Designed a Titan Extruder Mount for Anet A8. It's Mounted on the Left Z Carriage. The Idea Behind This Design is Similar to the Ender 3. ... To Install this Part, You'll Need Four M3x25 Screws to Secure it to Both the Carriage and X-Stepper Motor.

https://www.youtube.com/watch?v=clixTeZ3fJA - Corrected spacing for Anets smooth rods (46.3mm center to center - injection molded holders) - A huge Z offset was added to bring the assembly high enough for the E3D V6 without wasting z height,...

This Remix add BLTouch support.Support for almost any X belt tensioner designed for Anet A8.Print in PETG or temperature resistant filament.

- Any Nema stepper (I use the original stepper provided with the A8) - 3D touch (a clone of BLtouch) And its particularity is that it is designed to: - Use original fan, fan ducts or fan ducts designed to work with the original X carriage, like this...

Unfortunately, its original positioning proved to be a major flaw - the fan holder sits too high, inadvertently cooling the hot end rather than the filament emerging from the nozzle on my trusty Anet A8. To address this issue, I cleverly added...

The titan extruder mount featured here was specifically created for my Zonestar P802N, and it's likely identical to the Anet A8 setup. This custom mount is designed to fit snugly atop the plate supporting the Z rods and already incorporates...

This design also features: - Use of original Anet A8 bearing blocks or any remix if preferred. - Easy unmounting with only 3 accessible screws to remove the titan+ hotend + stepper block. Baseplate is a remix from scratch of this thing baseplate...

Here's how I did it: https://www.thingiverse.com/thing:2193695 and https://www.thingiverse.com/thing:2595525/#files This mount fits perfectly on all Anet A8 and i3 printers. A note: this mount needs to be printed with support material. ... Here are...

The printer's frame is modified to accommodate the Anet A8 and AM8, with a customized fit for their 46.3mm X rod spacing. To achieve proper alignment, the x offset is set at -28, while the y offset mirrors this adjustment at -28 as well. ...Note that...

It also accommodates almost any X belt tensioner designed specifically for Anet A8 printers. ... For an optimal fan mounting solution, consider trying this design: https://www.thingiverse.com/thing:1571526 Alternatively, explore one of these remixes:...

For the base, I designed it to fit the original Anet A8 acrylic frame, adding the extruder mount that was originally designed based on a design found at https://www.thingiverse.com/thing:2146021. The design requires M3 bolts for the extruder - two...

May revise later to allow for slight movement of the Titan if you experience loose gear mesh issues. ... 11/22/18 Added a block and pin option if you want to adjust the spool position slightly; you may need to scale up by 2-3% depending on your...

Conversion to Cartridge for Axle X + Adaption for E3D Titan Extruder The cartridges used are 11mm wide by 30mm long with an 8mm central hole. ...A video showing movement and some explanation is available at: https://www.youtube.com/watch?v=rLUHJkz0Ph8...

I require a replacement part for one of my sensors, and fortunately, I have a spare SN-04 Stock Anet sensor stored in my toolbox. ...To ensure seamless integration, I've decided to modify this part to match the firmware settings of my existing setup.

This design was created to be used with this carrier that functions very smoothly, better than IGUS and LM8UU bearings: https://www.thingiverse.com/thing:3031140 You should use this on the bed: https://www.thingiverse.com/thing:3039884 Note: I'm...

Ultra lightweight carriage for a titan extruder and an E3D V6 Hotend designed to deliver exceptional performance. Key Features: - Perfect weight distribution achieved by positioning the extruder stepper precisely alongside the rails. - Allows...

Titan Aero Extruder Enthusiast Unites as Fan

Models of Titan Aero purchased on Aliexpress

Titan Aero reinforcement to the right

I upgraded my Anet A8/Prusa clone's extruder with an E3D Titan Aero, utilizing a bracket that precisely fits 46mm X axis guide rod spacing and four sturdy 8mm bearing guide blocks. Hardware Components: 12 M4X12 SHCS screws Three sets of M4X20 SHCS...

The man was simply a Titan Aero decoy.

Mount the extruder titan aero to the printer Ender3 V2

Titan Aero Mount - A Revolutionary New Standard in Flight Technology

This is my carriage mod for Anet E10 with Titan Aero Extruder and 8mm Z probe. Two versions of Titan Aero handle are included, one with and one without a place for an 8mm sensor (I use P.I.N.D.A. V2). The fan with the cooling nozzle is mounted on...

This remix is based on RJFeddeler's BLTouch mount for the Anet A6 Titan Aero carriage, with some modifications to ensure smooth operation.\r\n\r\nAfter printing and installing the original design, I noticed that the BLTouch probe was slightly too low...

Titan Aero Pen Holder Installs Over Extruder Heat Sink Fan Requires 2x M3 Bolts

I modified a duct originally created by Gregory Holloway for his Prusa Titan Aero X Carriage, which can be found at https://www.thingiverse.com/thing:2192480. He had designed a neat bolt-on duct that I liked, but it didn't quite fit my Anet copy of...