tnc bluetooth 3d models
5731 3d models found related to tnc bluetooth.thingiverse
Custom case to enclose the wonderful mobilinkd TNC http://www.mobilinkd.com
thingiverse
WVCARC Case for TNC standalone version i did not design this only sharing it here so other people can make it Link to resource https://www.wvcarc.com/p/tnc-96k-resources.html
thingiverse
... a TNC for my Baofeng. ... Check out http://na7q.com/baofeng-tnc/ I felt like it should have a case to better protect it. Just slip the TNC into the sleeve then super glue the lid over the USB end. ...Only a light amount of glue should be used.
thingiverse
... TNC-Pi 9k from WVARC. ...I put it on the Raspberry Pi and wanted a case for the Pi 4 and the TNC-Pi 9k. https://www.wvcarc.com/2018/03/tnc-pi-9k-kits.html I use 4x 2.5mmx35mm Screws to keep it together. ...https://www.amazon.com/gp/product/B0789W9RNJ
thingiverse
The CM108 is a very common, cheap USB audio chip with a few GPIO which make it ideal for creating a TNC: https://www.aliexpress.com/wholesale?trafficChannel=main&d=y&CatId=0&SearchText=cm108<ype=wholesale&SortType=price_asc&groupsort=1&page=1 This is...
thingiverse
This mount goes inside of the taranis and holds a TNC PCB connecter like this:...
prusaprinters
The Tremor Nail Clipper (TNC) is an innovative assistive technology (AT) to enable humans struggling with hand tremors to clip their nails independently, thus helping with the day to day life. It clamps onto most tables (thickness under 5cm), and...
thingiverse
If you use 0110-M-P case (https://www.thingiverse.com/thing:922740) or a variant of it AND you wish to stack a TNC-Pi 2 on top of it, here is the solution! Print it and add it to your actual case as an extension. It will protect your TNC-Pi 2. ...
thingiverse
Mast mount for a TNC socket, usually used for WiFi installations. Requires 2x M5 nuts and bolts. ... Rotate 180 degrees before printing.
thingiverse
Mast mount for a TNC socket, usually used for WiFi installations. Requires 2x M5 nuts and bolts. ... Rotate 180 degrees before printing.
grabcad
This is a model of a Rosenberger TNC RF Sealed Bulkhead Connector that is used with RG-405 semi-rigid coax 0.085" diameter (p/n : 56K511-271N5)
thingiverse
Another remix. ...This time it will hold a TNC-Pi 2. If you do not want to stack them above the Pi, here you go! ... Enjoy!
grabcad
This is a model of a Rosenberger TNC Coaxial Bulkhead Connector that is good up to 10 GHz.It is mounted from the outside and with the locknut and nut inside the housing.Other comparable (but not exact) parts well worth considering are the Amphenol RF...
thingiverse
... the TNC should fit snug enough that it doesn't fall out. If you want to protect the button from getting pressed in error, you can insert the TNC so that the button is against the wall of the case. Hope others can get some use out of this. ...
cults3d
http://www.crazymakers.fr/videos-youtube/une_enceinte_bluetooth_diy_efficace_pour-art-iZiTeYY7cOs.html 🔹 Bluetooth module TDA7492: https://www.ebay.fr/sch/i.html?_nkw=tda7492+2x50w+bluetooth+4.0+board 🔹 M3x7 screws:...
thingiverse
Customized version of https://www.thingiverse.com/thing:356988 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=356988