toggle clamp latch 3d models

The clamp used in hotend installation now boasts slightly reduced tolerance (0.1mm instead of 0.2). Further optimization to Version 2 resulted in slight changes and rectification of previously identified errors. A modified version was initiated...

It may be necessary to adjust the drive gear position on the motor shaft so that its clamp bolt is on the stepper side. Additionally, ensure that the drive gear does not hit the guide during operation. Adjust the open position of the extruder with...

(Also contains STL files, as I'm mostly changing existing stuff...) **Design changes:** * Added slopes for more strength to the base of the Y axis, also added stops to the front to prevent the rods from sliding out * Designed a printable idler wheel...

The subwoofer prints in two parts which screw together, clamping the module (6x M3 screws). You need to remove the existing mounting tabs from the module. Use bluetack between the module and the frame to prevent rattling, with a clearance of 1mm for...

UPDATE 14/10/2019 Just got my hands on a flexi extension piece for the Tork Craft rotary tool: http://www.torkcraft.com/index.php?route=product/product&path=818_1227_1228&product_id=17747 Added an Arduino CNC Shield V3.0 running grbl 1.1h firmware...

... to the top plate files to make the holes non-countersunk.- To mount a Neutrik passthrough you will need the 2x M3 12mm countersunk hex bolts and 2x M3 nuts.  The Neutrik passthrough will be a tight fit and may need to be clamped into place.

Also I needed to clamp the two halves together and then run a 3mm drill bit down the centre to properly clear out the hollow for the cable. After that, surprisingly easy to assemble.</p> <p>If your<em>right</em> pivot pin breaks you can use this only...

Use a cut piece of carbon fiber archery arrow to align the wheel halves when gluing them and clamp the halves until the glue sets. The black wheel rim and hub rims have a good press fit on the finished wheel but can be glued if necessary. The barrel...

Bolt the upper housing to the main housing, clamping the membrane between both parts. Put a larger spring around the plunger, put the plunger on the membrane and scre the top cap on. <p class="detail-caption"><strong>Section view of the whole...

It might be very difficult to press the base into place so, I suggest using a C-clamp to slowly apply pressure until you hear it snap into position. ...The parts are designed to fit together tightly to prevent jiggling but if the "case" doesn't fit you...

I did NOT create a stop piece for setup, as you can easily use a clamp and scrap materials to the same effect. After printed parts were removed from printer, I used some sandpaper to touch-up the long faces of my prints (there was a little...

You can tighten the screws reasonably hard since the mount is held in place via clamping force. Your particular M3 screws may or may not fit through the holes in the Raspberry Pi. If they don't fit through, use appropriately sized drill bits (by...

Therefore we designed a clip you can clamp to your sun visor in order to hang there all types of masks. If you have a regular face mask, or an ffp2-mask - no problem, you are going to find a way to stick it to your sun...

Just use these spacers and be very careful to NOT OVERTIGHTEN the clamps, its a glass tube. My parts were all aligned properly by the spacers. You still have to adjust the mirrors to align them, I have an alignment tool for that too. My one...

Because I'm going for the most elegant and slim design, I've decided to modify the Titan's hot end clamp. This saves plastic, which in turn shaves off valuable grams. Also, because of this new, strange hotend mount I have to make my own hotend out of...

The clamps hold the mirror well, so all is good. After some time, I noticed that many printers have a system to clean the nozzle before each print. Some have even made their own versions on YouTube. So, I thought to take advantage of the extra space...

Sinch it all down with a hose clamp. There's no need to cut the vent tube flat to the wall or anything. Though, you may need to trim it back. Apply some sort of gasket material to the flat side of the wall flange. I used neoprene strips cut to...

Update, I have made a new version with an integrated holder for a bltouch inspired by Humanity_co, if you have already printed out the previous version then you will only need to print out the fan shroud clamp and a small adjustable mount files:...

Alternatively, I'll attach holders/clamps to the side curtain rails so we can secure the bed quasi at the ceiling during the day and use the seating group without demounting the bed. This is an example of how 3D techniques can be used in the DIY...

Once the cap is in place, clamp the trap over the cap and turn it upside down to set and cure.Trick: The ball prevents the trap from opening so in order to get it open, you first need to get the ball out of the way. This is done by turning the trap...

Also added a mounting clamp to allow bolting the connector. ...Both come from this case: <a href="https://www.thingiverse.com/thing:3631413">https://www.thingiverse.com/thing:3631413</a></p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p>...

You'll need 5x M5x15mm screws to clamp it down on each side, along with suitable nut bits underneath. I had spares hanging around from a previous project, but if you don't have anything then just do a search for T-slot nuts. Also two M10 nuts per...

The Drive Wheel Plug (two per wheel) replaces the bearings at the motor end, allowing it to be clamped and driven by the M5x50mm screws that have pulleys on them. Tighten the M5 nylon locknut to secure in place. Take note of the 1mm thick precision...

To assemble the masses use a vice or clamp to hold ten washers together. Apply Bondo to the outside of an aluminum spacer and push it into the washers. Make sure it has sufficient bonding agent to stick, then wipe away excess. Let cure. Repeat...

Other parts designed for my printers include: - http://www.thingiverse.com/thing:1959901 (GT2 belt clamp (Prusa Y-axis)) - http://www.thingiverse.com/thing:1937232 (Arduino Mega and RAMPS v1.4 case) - http://www.thingiverse.com/thing:1905409 (Prusa...

Print Settings Printer Brand: Solidoodle Printer: Solidoodle 2 - Pro Rafts: No Supports: Doesn't Matter Resolution: 0.3 Infill: 30% Notes: only support needed is under the motor mount on the "slider" This needed to be narrower to fit inside the 36mm...

The base can warp, use appropriate settings or clamp the corners to the bed after the first 25 or so layers. Generic print options like 3-5 walls and top/bottom layers and 15%-30% infill are perfectly adequate. There are 4 additional holes for...

But, I wanted to run the belt through the inside of the Makerslide for a cleaner look. This is still very much a work in progress, I'm currently working on completing the design and building the printer. I'm posting a build log on my blog:...

Do make sure to balance your pressure with loosening the clamp bolts to allow the freedom of movement, and watch out for cracking the plastic with excessive force. Use a right angle block to place against the bit edge (I recommend mounting a 1/2" or...

The antenna mount boom is designed to be clamped between the tripod and the VRx enclosure. There is a second hole on the tripod end of the boom to lock rotation on video tripods. A 1/4-20 bolt stack (washers both sides) is used to attach the antenna...