tomtom holder for car 3d models
2393025 3d models found related to tomtom holder for car.thingiverse
This is a Holder for the iPhone 5 which fits in to the car mount from TomTom. So you don't have to change the whole thing. ...You just have to print out the Adapter and bye a little converter for the plug.
thingiverse
A simple adapter for the Tomtom Rider to fit on a common car system. Glue the two parts together using CA. ...Bottom edges flush and position between the two side markings.
thingiverse
TomTom Rider moto navigation holder for Honda Africa Twin CRF1000
thingiverse
tomtom holder for opel karl. maybe suitable for other make / models. ...
thingiverse
Tomtom holder for CD Slot. Works perfectly on Mazda MX5 NC. Add v2 : Round Corners Prefer ABS ou PET. ...PLA won't resist in summer with high temperature
cults3d
TomTom plug holder for motorcycles The plug holder attaches the TomTom plug to the motorcycle. It protects the plug from corrosion, moisture and sunlight. The plug holder is fastened with two cable ties. The solid grip of the connector is achieved...
thingiverse
TomTom plug holder for motorcycles The plug holder attaches the TomTom plug to the motorcycle. It protects the plug from corrosion, moisture and sunlight. The plug holder is fastened with two cable ties. The solid grip of the connector is...
cults3d
Needed an holder for a very good GPS (oldie) . ... Part list: 2 x M4 bolt and nut Thank you for sharing the knob nut https://www.thingiverse.com/thing:641854
thingiverse
Needed an holder for a very good GPS (oldie) . ... Part list: 2 x M4 bolt and nut Thank you for sharing the knob nut https://www.thingiverse.com/thing:641854
thingiverse
I normally use Brodit car mounts for navigators, but aparantly Brodit doesn't trust the EasyPort. This ring fits the navigator really tight and keeps it firmly attached to the Brodit mount. It can be attached to a standard Brodit ball coupling...
thingiverse
ABS support for cars or other places with a flat zone. ...The first layers are printed in TPU that will give us anti slide and better stick with the hot bed.
thingiverse
This thing is for a Tomtom Via 160 satnav. It replaces the universal type holders which are sold to hold smartphones and various satnav units. These units are often bulky and fiddly to adjust and don't always hold the device securely. This design...
thingiverse
Holder for Tomtom Rider 5xx snugfit on Energica EVA handlebar
thingiverse
Replacement for the TomTom iPhone 3/4 Car Kit part. Uses existing fitting, and gives a simple frame for an iPhone 5/5S in an existing book/wallet-style case. Although it's designed for my specific iPhone case, the ball-joint socket fits well (when...
thingiverse
I was looking for some holder for my Tomtom found nothing. This is what I do. I pasted a little armaflex inside the holder to allow the GPS to get stuck properly without it moving in the holder. This works perfectly for the motorcycle. ... I mount a...
thingiverse
I created a holder to fit my tomtom rider 450 to the 12mm tube where the genue BMW Navigator was mounted. ... Infill 50% PETG CF 0,1mm Don't tighten the screws (2x M5x25mm with 2 washers) to much!
thingiverse
After fixing a TomTom XL which had it's USB SMD socket ripped off, I needed a simple attachment device for my Toyota Hilux, Using a three (3) piece design, a ball/socket mechanism allows rotation of Tomtom and the cupholder clip allows cradle to...
thingiverse
Since the original holder for my TomTom Rider is not compatible with my Ducati Diavel 2011, I designed my own special mount for it. Despite the strong vibrations of the V-Twin the Ducati had so far (about 300 km driven) no problems with the printed...
thingiverse
This is a holder for GPS devices of the TomTom 600 and 6000 series. The base is designed to fit into the spacing between the car radio and the upper vents and is arranged in a 30 degree angle to the casing because that one is angled - other wise the...
thingiverse
Thing design allows to put a TomTom Rider Navigational device at the 12mm handlebar reinforcement of usual cross motocycles I recommend to print this with PETG or ABS due to thermal influence of the sun outside. ...
thingiverse
Should be printed using a flexible material (if not, you will not be able to get it over the hinge without disassembling it). ... Should also fit Tomtom Runner 3 and Spark 3 (let me know if it fit!) Try printing with 100% infill.
thingiverse
Motorcycle support for TomTom Speed 35 mm/s - temp. ...240° extruder / 70° bed layer fan 60% from the 6th layer required material: N° 4 hex nuts M4 N° 4 screws M4 x 40mm
thingiverse
This is a replacement mount for the (vintage) TomTom model One XL. It requires an original mount to attach to the gps-unit, and a [Biltema model 22178](http://www.biltema.dk/da/Kontor---Teknik/Mobilt/Holder/Universal-mobiltelefonholder-2000021405/)...
thingiverse
TomTom XL and XXL adapter for garmin support (garmin support for 595,590). With this adapter you can mount Tomtom over garmin adapter. ... Edition_ V2 - With reinforced edge
thingiverse
For the lucky owners of the queen of the motorbikes Honda CBR1100XX Black Bird, here a support for TomTom navigator. ...I think it is customizable also for others motorbikes.
cults3d
Holder for mounting the receptacle for the TOMTOM Go NAVI. Hole spacing for tomtom xxdock 38x30 (mm) (wxh) If you need other hole spacing, just message me then I will make you a special version ready. For mounting, 2 original screws must be removed...
thingiverse
Search for 'free stl viewer' to find one for yourself. Instructions Just view yourself in the 'Thingiviewer' to see how cool you look in all 3 dimensions, or download yourself as an .stl file. To...
thingiverse
Thing moved here: https://www.youmagine.com/designs/tomtom-start-60-m-car-mount-kit I do not support companies forcing lawsuits based on trivial patents against other 3D printer companies. This kit comes with two connectors: one for standard...