toothbrush cup 3d models
47636 3d models found related to toothbrush cup.thingiverse
Initial design for a toothbrush cup holder to replace a broken glass one. Made for circular wall-mounted holder with inner diameter of 57mm. Printed in three parts - body, base and lid. ...For base, two options are available - solid or with mesh...
thingiverse
I designed this toothbrush cup because the original glass broke. The cup has an diameter of 54 mm and is 70 mm high in total. The inner diameter of the cup is 51 mm. The cup has a hole at the bottom for residual water. Support is not mandatory...
thingiverse
A simple toothbrush cup with a water strainer and base cup to avoid water stain. The cap and base can be taken off for cleaning purpose. Holes in the base are allowing air to flow and dry water trapped in the very small recess, they can also...
thingiverse
Cup for your toothbrushes. ... As always I included the .f3d file so you can modify it.
cults3d
Give a different and fun touch to your sink with this cute tooth-shaped cup for your toothbrushes.
thingiverse
Replacement cup for toothbrush/cream holder. ... Print Settings Printer: Prusa I3 MK2 Rafts: No ...
thingiverse
This is a cup to store your toothbrush on the sink, with holes so that the water will drip out, and extra balance support. Instructions Will need some support for the base area, which is elevated.
thingiverse
Can hold up to 4 toothbrushes without them kissing each other. Clean small design. No drain holes. ... Specifications: D = 50 mm H/D = 1.618
thingiverse
I created a tooth burst cup, because the glass one was broken. ...It is customizable.
prusaprinters
Thise is a replacement cups in case the original glass is broken. The diameters of the cup areupper section: 69mmlower section: 59,2mm
cults3d
My cup was broken. ... It seemed simple to me to print one with a few flowers around it.
thingiverse
Replaced the broken glass toothbrush cup in my fathers camper with a less fragile 3D-printed one.
cults3d
Here is a simple toothbrush cup /tooth. The model is 118x114x126mm Large and is also needed in this size because otherwise the toothbrushes do not hold properly. ... (Minimally scalable down)
thingiverse
Simple toothbrush cup. Approximately 75 mm tall. This was made with the amazing Autodesk Project Shapeshifter (http://shapeshifter.io/). Instructions Print the thing, put your object of choice for...
prusaprinters
This is the replacement for the original glass Grohe toothbrush cup. Print instructionsI printed this in Form Futura HDglass Clear filament. ....1mm layers, 30% infill and no supports.</p>
thingiverse
Bathroom Fenestrated Toothbrush Cup 10x10x10 cm It is also suitable for office use. Print Settings Printer Brand: MakerBot Printer: ...
thingiverse
If you have ever experienced a problem with your toothbrush cup and mold or your toothbrush smelling bad because of humidity, this cup is going to help you. The model consists of the cup itself having a grid at the bottom. The second part is a small...
thingiverse
Built as treat for my huge Batman fan son (which delighted him) I present a themed toothbrush cup. It's built as a two piece to allow printing the cup vertically and avoid the use of supports. Has a conic inner bottom and water escaping holes to...
thingiverse
Obviously, after planting it there on the sink my bird noticed our toothbrush cup is out of place. I wasn't able to find anything similar so I decided to make one myself. The hex pattern is a close resemblance, same dimensions to the soap dish. Its...
thingiverse
Now it has become a toothbrush cup that was just needed. I adapted the code to the coffee mug (https://www.thingiverse.com/thing:1019175) and redesigned it for my purposes. Many thanks to PocketBrain for the inspiration. Ich arbeite mich gerade...