top remix 3d models
405370 3d models found related to top remix.thingiverse
Just a remix of the original Peon 230 top plate. ...It allows to mount two foldable antennas for RX.
cults3d
Remixed the top portion of the candy machine. ... Sealed the hole in the back and made the diameter of the indentation larger where the pin fits into it.
thingiverse
This is a remix of the original top found here http://www.thingiverse.com/thing:542914 The original version made me think about having my students design a top given a set of specifics that would driven by overall size and material usage. The...
thingiverse
Remixed the top portion of the candy machine. Sealed the hole in the back and made the diameter of the indentation larger where the pin fits into it. ... Also made the diameter smaller where the screws go for a better fit.
thingiverse
... balanced. Edited in tinkercad. Inception Top is thing http://www.thingiverse.com/thing:23686 Pumpkin is thing http://www.thingiverse.com/thing:167043 Would love any input you have! ...Please share your prints if you have a successful print of it!
thingiverse
This was remixed from potentprintables's [Spinning Top with Articulated Arms](https://www.thingiverse.com/thing:2859478) I split that file apart for dual extrusion. I have a lot more designs so be sure to follow me here at [Polymathic...
thingiverse
Remixed the lid so that I could have an additional lithophane here. ...Unlike the others it needs to be glued in
thingiverse
I have printed the original Lighthouse Top, at both 0.25% scale and 0.40% scale - on both occasions I had issues with the very top of the canopy - it became very thin and produced small gaps near the very top. Pictures show the effects before and...
thingiverse
While printing Ozpin's cane by MTriton (https://www.thingiverse.com/thing:705243), I noticed that the cain top was missing some detail. ...I decided to make it slightly more accurate by adding the four little nubs under the outer ring.
thingiverse
... 4 and not have to print them one by one, and if you use a brim you can use a standard setting without the print falling over. original Dovahkiin Helm Reforged by MHypothetical https://www.thingiverse.com/thing:1979664/remixes tell him he is awesome
thingiverse
-> "Egg Top Remix.stl" The base doesn't touch the top of the egg (gap of 0.3 mm) Print Top and bottom at the same time, like in the picture, with multiple color filament to have a good joint of the colors ^_^ No raft needed for egg parts with Egg Top...
thingiverse
Remix for (https://www.thingiverse.com/thing:922740). ... Top Part without cable slots.
thingiverse
This is a Remix of the top for https://www.thingiverse.com/thing:2193849 with "HEAT" and COOL" added above each outlet.
thingiverse
I printed the bottom and bolt from this thing, but remixed the top. I thought the razor could be mounted a bit better in the top part of the cutter. Thought it could be a bit firmer. You can now slide the razor into the holder and secure it with 3...
thingiverse
R2D2 top dome pie remix of mr baddleys awesome r2 work. I didn't like how the top piece was loosely on top (hard to position perfect) so I added a lip so it can keep the part center and snaps flushly in place. it sits flush on the under side too...
thingiverse
... changed are - Frame_NoSwivel.stl and Hook_Square. The rest of the files are created by dashfort22 and are unchanged. I also added a missing thumbscrew to clamp the phone from another remix, not my file but can't remember the name. ... Good Luck!
thingiverse
I've adjusted the text and cleared the calibration hole. ...Nice case though, thanks!
thingiverse
Needed this to have the police call box words on it so i put some on.
prusaprinters
<p>I've adjusted the text and cleared the calibration hole.</p> <p>Nice case though, thanks!</p> Category: Electronics
thingiverse
... remixed this amazing console case for the PI... ...I just changed the top so you'll need the other parts from the original. Which is here: https://www.thingiverse.com/thing:2471701 For the top I added a bezel to keep the screen in, and a stylus holder.
thingiverse
This is a remix of UCO Candle Mold /w tapered top #4744173. A friend had some problems with the slot in the main candle mould. So I made it a little bit wider. There are some issues with the thingiverse upload form. It won't accept the Remix...
thingiverse
remix of the top Clamp. Added holes for the rubber suction cups, threaded the hole for the main lamp and zip tie holes to support the wire. ... You'll have to go to the original design for the fastening clip part.
thingiverse
This is my remix of [Wave lamp Yeah!](https://www.thingiverse.com/thing:2109502) by brico3d I have just adapted its size and made the top open. ... To print it, rotate it to start the print with the wider side on bottom.
cults3d
This is a remix of Z Top for Prusa Mini. Blue chinese couplers have 14mm diameter and does not fit into this part. That causes to loose some Z height. ...I enlarged the hole and put some material to cut outs for smooth rods.
thingiverse
This is a remix of Z Top for Prusa Mini. Blue chinese couplers have 14mm diameter and does not fit into this part. That causes to loose some Z height. ...I enlarged the hole and put some material to cut outs for smooth rods.
thingiverse
I ground down the small diameter rods, but decided for the 12mm rods to modify the Z axis top so that you can slide the rods in after the axis top is in attached to the frame. This design also makes it easier to ream the 12mm holes because the...
prusaprinters
Inspired by the tank visualizer https://www.prusaprinters.org/prints/88302-tank-shaped-z-axis-motor-visualizer-for-prusa-mini for the Mini, I wanted access to the lead screws on the MK3S/+ to add my own take on a visualizer.I remixed the z-axis top...