towel bar holder 3d models

These simple towel bar brackets use a 1/2" tube between them. There is a recess on the wall side that is for a Command Adhesive strip - I use the water resistant strip. ... I happened to have a 1/2" aluminum tube but copper might be nice also.

This is a simple "shelf" soap holder for a shower where a towel bar is available. I stacked three of these in my shower for a shampoo bar, conditioner bar, and plain old soap bar. This keeps the soap bars away from the direct shower spray so they...

I had a failure of one of the wall mounts for my Moen Eva towel bar. After scouring the web and calling Moen, the part alone is not available (you must re-purchase the entire item if not under warranty). So, I took some time and designed this mount...

When you don't want to leave a towel around to collect germs replace it with a roll of your favorite paper towels, suspended from the towel bar in your bathroom. Print instructions Print 2 copies of the Thumbscrew Print 1 copy of the left hand paper...

This is a 30cm wall mount (siliconic glue) towel holder, it can move about 45° on the left and on the right, inside the bar there is a 5,4x212mm hole, to fill with (in case) a steel round bar to increase strenght. fixing and mounting are 2 caps...

These can be used with the over-the-wall towel rack and bottle shelf designs as seen here:http://www.thingiverse.com/thing:1193014 and http://www.thingiverse.com/thing:1731973 In order to add hooks or a scrunchy holder to the bars. ...Note that the arms...

The "papertowel_bar" can be slotted through these extensions to provide support when tearing paper towels from the roll. Print "papertowel_bar" and then remove the support material from inside the connector holes. ...Once complete, drip a few drops of...

I made this as a way for me to learn how to use fusion 360. I like the way it came out so I figured I'd share it with the maker community. You'll need to rotate the pieces in your slicer application to print in an orientation that makes sense. ...

There are towel holders to be found for this purpose, however, they won't lock onto the heater bars, which is frustrating, since they fly off everywhere when you grab your towel. Therefore, I adapted the snap-in mount from the TP holder. In order...

Requires eight 5M x 25mm socket hex cap screws. Six 5M brass plastic thread inserts. Two 5M nuts with washers. ... My printer is fairly dead on and fit was good with only minor adjustments needed.

This is a simple towel bar holder.

Standard towel bar accessory holder to use with stainless s-hooks; can be modify to accept more hooks or to individualize the hook placement. ...

An OpenSCAD towel bar.

Four kids, one towel bar...These snap onto my 15.75mm diameter towel bar so they don't fall off when the kids pull off their towels. I made them extra wide for strength. ...

My Wife wanted some hooks for her towel bar to dry luffas and things. This is the simple design I made. ...Should clip right on to most standard towel bars.

Wood required for the bar. Print instructionsI needed a towel bar for the laundry room. I designed these brackets and used scrap lumber (26mm x 38mm) for the bar. Designed and oriented so supports are not necessary. ...Printed in PLA with 20% infill on...

These are sized and meant to be used with a piece of 3/4 pvc pipe to make a towel rack, but they'd also work for a paper towel holder or toilet paper roll holder as well.

This is a replacement for, I believe, a Delta Crestfield Towel bar. ... The mounting hardware for one side was lost and I created this as patterned from the other side.

Four kids, one towel bar...These snap onto my 15.75mm diameter towel bar so they don't fall off when the kids pull off their towels. ...I made them extra wide for strength.</p> <h3>Print instructions</h3><h3>Category: Bathroom Print Settings</h3>...

The original part is still available for those who would like a stronger part (3.5mm thick).If you are feeling fancy there are printable friction fit Finials to pretty up the ends of the towel bar. There are separate files for the Finials if you are...

If you are feeling fancy there are printable friction fit Finials to pretty up the ends of the towel bar. There are separate files for the Finials if you are using SCH40 or SDR21 as the inner diameter of these pipes are different. If you found...

This is a four piece towel bar with dovetail joints and two adapter caps that can be adjusted to fit almost any towel bar setup. This specific setup is for a shower towel bar (45cm + (2)1cm caps). This has been printed and tested without issue but is...

I was getting irritated by the always sagging swivelling towel bar next to my sink in the bathroom. So I decided to design a replacement. This is a single towel bar that swivels horizontally. It was designed in OpenSCAD and in printed in neutral...

Here is a simple solution: A sturdy 3D Printed towel bar mount. This (customizable) mount is designed to hold a 19mm bar with four (4) 4mm screw securley in place, prefereable above your radiator. Distance to the wall is 70mm, enough room for an...

This is a Fusion 360 design for a towel rod holder.The rod is a piece of 1/2" PVC pipe about 17" long. The end caps are a snug fit. ...It is an easy print without support.</p>

The towel bar kept falling off; the culprit was a broken metal bracket. The friendly man at the hardware store said 'no, we don't sell those, you have to buy the whole bar kit' but I made my own copy. I happened to have a 2mm nozzle in my Ender 3...

Basic kitchen towel hanger, hangs to the top of pull cabinets, needed something that looked nice and didn't need to make holes in the wall

Towel holder

Towel holder

Towel Holder