tp cast for vive 3d models
2233577 3d models found related to tp cast for vive.thingiverse
EyeTrackVR Hardware for Vive & Vive Pro (they have the same lens) ESP mounts are mounted with double sided tape You'll need to print one of each plus a mirrored version of the LED mount for the left eye. Repeat but mirror everything for the right...
thingiverse
This is a snap in perscription (or possibly non-perscription) lens adapter system for the HTC Vive that takes a common set of lenses you can order online cheaply from zenni.com. There is a frame piece that it held in with friction and then a lens...
thingiverse
Where to put the HTC Vive when not wearing it? This seems to be a relatively widespread issue. Here is one solution: hang it. Fix this hook to the ceiling and get it out of the way. As the cables are routed from the ceiling as well this is probably...
thingiverse
I took inspiration from several projects, but the actual attachment grips are from https://www.thingiverse.com/thing:3141858 (Vive Wireless Adapter Modular Battery Bracket). I used a Noctua 40x10 5v PWM fan (Amazon...
thingiverse
resized and sliced for Legoman TP Holder I used 3D Solutech Chocolate Brown (https://amzn.to/2SKOl7H)
myminifactory
A rifle controller for use with the HTC Vive VR headset and room scale controllers.
thingiverse
Wallmount for my 5 port TP link switch. The switch is 100x100x25mm. ...As I only have a small printbed, I had to split the each holder into 2 parts.
cults3d
I like to print these https://www.thingiverse.com/thing:2613740 and use TP rolls for storage. ... I created this wall rack so they have their own place :) I printed this with 5% infill and 3 perimeters.
thingiverse
I like to print these https://www.thingiverse.com/thing:2613740 and use TP rolls for storage. ... I created this wall rack so they have their own place :) I printed this with 5% infill and 3 perimeters.
thingiverse
... will be stable on table. ... I did use double sided tape for attaching items together. Supports are compatible with Lego, there is also small test part, if you like to be sure that fitting is good. ... Scale whole part regarding your fitting.
thingiverse
This is a mount for the Vive Facial Tracker and it's compatible with both Vive Pro and Vive Pro Eye. Tip: Print it sideways for best results. Heat may affect PLA so I would recommend using a heat-resistant material. ... You can get the Vive Facial...
grabcad
DESIGNING A FIXTURE FOR MILLING OPERATION IN A SQUARE CAST.
thingiverse
This is a revision of Vive Stock by hapteck, published Mar 26, 2017 of the top piece that is on the Vive controller and the mount for the rail for magnet. it seems that the original is made for .75" magnets and the magnets listed are 1"(1002304). I...
thingiverse
This is a gun stuck you can slip onto the end of a HTC Vive controller for a more real gun feel in VR games. ...You should be able print as is, but you may need to change it's orientation depending on the size of your printer.
thingiverse
Stand for HTC Vive BaseStation. You can install the base station towards the UP or DOWN at an angle of 30 digrees. 30 digrees UP-mode is for installing the base station on the floor or near. DOWN-mode is for installing the base station on the shelf...
thingiverse
...... Edit it online https://www.tinkercad.com/things/11LP0WURXf0-10-rack-fuer-tp-sf1005p To be able to install a small PoE switch in a 10 inch server rack, I designed this mount with Tinkercad. Because of the struts the mount is very torsion resistant.
thingiverse
VRProtect, prescription lens holder for HTC Vive, edited so it's printable. All the info you need is on the original page. Relevant links below. ... Original: https://www.thingiverse.com/thing:1639833 Glasses, 40mm:...
thingiverse
The cable mount from RichWP was a much needed upgrade for the Vive, yet I found the actual belt clip a bit to easy to dislodge from your pants and also a bit too small when fitting with the cable holder. I therefor combined it with the belt clip by...
thingiverse
A rifle controller for use with the HTC Vive VR headset and room scale controllers. This Thing is based on remixes of several Things listed in the Remix Sources section below. The Rifle Controller for HTC Vive has been tested with H3VR...
thingiverse
This mount has a flat clip that can mount between the stereo cameras of a vive pro. ...The clip allows you to take off the leap device so you can use the cameras again.