tpu filament 3d models
199655 3d models found related to tpu filament.thingiverse
TPU filament holder on spool with handles : easier to hold. I printed it with a 0.4mm nozzle with 2 walls and 0% infill, and 3 bottom/top solid layers : that way it's more flexible so it holds better and it's still easy to put the filament in. ... I...
prusaprinters
Both hook and buckle use less than 1/2g of filament. To use, poke one end of your 1.75 mm TPU filament up through the slot and pull taut, loop around the U-channel maintaining tension on the cord. As you tension the cord, it gets squeezed...
thingiverse
It is intended to be a design experiment, using flexible TPU filament. Please rotate as necessary to fit the strip on the printer bed. Once it is printed, one should fold it in a way that allows for the same letters (A or B or C) to show up on one...
cults3d
It is intended to be a design experiment, using flexible TPU filament. Please rotate as necessary to fit the strip on the printer bed. Once it is printed, one should fold it in a way that allows for the same letters (A or B or C) to show up on one...
thingiverse
The sides and end trays are printed using a flexible TPU filament to allow the harder, PLA flanges to fit inside them without much slipping. The whole design is modular, so you can either print a single tray or stack as many as you need. The...
thingiverse
A new design for feeding TPU or any flexible filament without it looping around the drive gear. ... Works on any filament, easy to adjust.
thingiverse
One more Cable tie which printed using flexible filament (TPU). Nothing special but rather convenient. ... Choose fix variant by the diameter of the cable you use.
thingiverse
... Gold: https://www.youtube.com/watch?v=eSOwQyhV0WQ&t=4s Gasket size: 1. 120mm X 120mm X 1mm 2. 140mm X 140mm X 1mm Printer Creality Ender 3 Printing: TPU transparent plastic nozzle 220 c. bed 40 c. ... layer 0.2 Model Printed 100% infil.
thingiverse
You can now enjoy Push Pop Fidget ※This is based on the assumption of TPU filament. ... Maybe a little thin...
thingiverse
Tri-tetraflexagon for Flexible TPU Filament A tri-tetraflexagon with six 25mm x 25 mm squares; note that the 7th square overlaps with another to form a loop. I started this as a design experiment using flexible TPU filament, which turns out to be a...
thingiverse
This is not capable for flexible (TPU) filament family. I found some design in the net and in thingiverse. But... I can't found a right version for my MK8 type. So, I attached my version for this problem. This is a working model. Please setup your...
grabcad
This is a filament run-out sensor, especially used for TPU and other flexible filaments.
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
After still having problems with ones on thingiverse, moved the hole slightly to the left and then opened it up. If you now drill out the ptfe tube holder and feed the ptfe through completely and then with a knife cut to the same contour as the...
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
General Electric Food Disposal Sink Strainer (use TPU filament)
thingiverse
You Can use this design with a classic TPU filament !!!
thingiverse
This case just can be printed using flexible filaments like TPU or TPE
thingiverse
Modded my i3 Mega to print TPU/TPE, found that because the filament is so soft it tends to go into the extruder at an angle so created this to allow the filament to go into the extruder nice and true.
prusaprinters
This is a really simple dust blower. Print it from TPU or a similar flexible filament. Make sure that especially the tip gets enough cooling. ...If the hole is not the right size, you can simply cut off the tip or heat a metal wire or similar and...
thingiverse
Ein einfacher aber sehr wirksamer Mod um mit dem Anycubic i3 Mega TPU zu drucken. Unter Umständen auch für andere Drucker anwendbar. Oben ist ein M6 eingebracht. Die Durchgangsbohrung hat einen Durchmesser von 2mm. ... Ich habe das Model...
thingiverse
... frequent replacements, and allow higher print temps. ...Or.... order in metal from shapeways! If someone wants to print one in PC and send me one I would appreciate it "wink wink". I've gone through 9 versions of this, it will print TPU very reliable.
thingiverse
... ...You can define what flow rate you need to test in each 10mm to get the optimal flow rate for you printer and your filament. I added the CAD file in case you need to modify the model. ... You can check on the youtube video for more detail
thingiverse
You can use this shield with a TPU Filament! ...watch this tutorial https://youtu.be/26pnzRs-xM0?t=261
thingiverse
NanoHack 2.0 TPU filament strap clamp. It can be adjusted and clean up easly. ... - 2 x bolt : M3 x 8 mm - 2 x nut : M3
thingiverse
Somit lässt sich TPU Filament verarbeiten, ohne dass der Bowden Extruder umgebaut werden muss. Der Druck des Teils geht sehr schnell. PLA ist hierfür ausreichend! Viel Spaß beim Drucken! ENGLISH: With an Anycubic I3 Mega you can also print...