track holder 3d models

Build this holders to create a cheap custom hotwheels track for my 1 year old kid. Used 8 pieces to hold the track in the picture. ...

Duplo train track holder.

E-Track latch holder, E-Track latches slide in from the side to keep them organized. ... I couldn't make it large enough so they would latch in normally without having issues keeping them in.

curved camera slider track holder, detailed and used here: http://transistor-man.com/semicircle_track.html

Duplo to Brio Track holder. ...Minimalstic design for fast print time.

This will fit any wooden train track that is 4 centimeters wide. It's designed for the Ikea train tracks. ... Dimensions: 8cm x 5cm x 1.5 cm Print however you desire.

This Remix flipped the orientation so the tracks are facing up and the brick interface provides more fun and options.

If you have a similar slotcar racing track from the early 1980s you'll probably need to make a bunch of these clips like I did. ### Printing tips The pictures show a few clips I printed, all at the same time, at a resolution of 0.28mm to save...

... wall built from standard pegboard. ... I made marble tracks out of 1X2 routed out in the center. ... Video of the marble wall: https://www.youtube.com/watch?v=Nlbvtgsc9Qc Video of the marble elevator: https://www.youtube.com/watch?v=lR80fKhOkMA

... marble wall built from standard pegboard. ... I made marble tracks out of 1X2 routed out in the center. ... Video of the marble wall: https://www.youtube.com/watch?v=Nlbvtgsc9Qc Video of the marble elevator: https://www.youtube.com/watch?v=lR80fKhOkMA

... area is not covered by this holder. The tiny cubes fit loose in the holder so you can change them during the game easily. As I own a quite small 3D printer (M3D) I had to split the holder into two pieces which are glued together once printed.

just a track to fit various kinds of LED strips. read comments for more appropriate variable sets within the scad. the "heat shrink" refers to normal heat shrink because i often use clear heat shrink to waterproof LED strips instead of the terrible...

I made this bc I wanted to up the strength of gravitrax rail pieces. ...introducing the gravitrax 2 - Rail Holder.

Having used the Systainer Rail Holder for Parkside PTS1200 C2 Rails, I found how convenient they were at holding the rails to my systainers on a cart and moving them horizontally , however I have the FSK-420 which is significantly larger. ...

I was tired of having to carry the saw track seperatly, so I designed this track holder. It's placed in the cardholder on any systainer and holds the track pretty secure. ...Just be aware that the systainer hangs leaning to the side where the track is a...

A bit bigger and more rigid construction.Fit 1,1 x 0,5 cm magnet.Track fit perfect on the holders now.

Simple holder to keep them pesky population cubes in the right place. ...Remixed from: http://www.thingiverse.com/thing:874719 simply made a full version so I didn't have to glue.

Based on timbologist's OO/HO TRACK PENCIL HOLDER, I redesigned it to be able to use other pens like Lumocolor, which I preferred.

A simple marble track holder for a 3/8 wooden dowel. It has a vertical piece along with four side slots to attach multiple holders together. It also has four small holes for mounting screws. This is is meant for my DIY Olympic track set which can...

Track pump holder. Original holder has been removed as this was for a smaller pump. (If you have that file you can print at 135% and it'll work. V2 now uploaded. ... Designed as I needed something to secure my pump in my van.

Basic track holders

Single segment of my T-Track Accessory Holder that allow custom spacing.

Single segment of my T-Track Accessory Holder. ... Allows you to customize how many and what distance apart the accessories are.

... 4 stacks of 8 duplo tracks, for a total of 32 tracks. With the studs on the top, you can also put a brick on top to hold them in place. And as a bonus the holder is exactly the height of 6 duplos, so can work as a support for overpass tracks. ...

Wall (or garage door, workbench legs, ...) mounted holder for Einhell circular saw track/guide. Re-make of popular Festool holder adapted for Einhell's track size. Print all 3 parts at the same time (Z-flip peg if necessary) then assemble by...

Designed up this initiative track holder to use in Chronicles of Drunagor: Age of Darkness. You can print 3 or 5 of them to avoid unintentional movements during the gameplay. Printing: No supports required. This is my first published...

This is a scale touch for my 1/16 RC Tank. there are 2 options to print: 1. Separated sections (not advisable unless you have a extremely good printer), you need to add a pin to join them 2. ...Both parts together with the pin.

This is a scale touch for my 1/16 RC Tank. there are 2 options to print: 1. Separated sections (not advisable unless you have a extremely good printer), you need to add a pin to join them 2. ...Both parts together with the pin.

Single track version of the spool holder from the Airtight Filament Container, should work with most large and medium spools. Uses 4 - 608 Bearings*. Bearings are inserted from the bottom of the spool holder. More of my designs for printers can be...

Single track version of the spool holder from the [Airtight Filament Container](https://www.thingiverse.com/thing:2607131), should work with most large and medium spools. Uses 4 - [608 Bearings*](http://amzn.to/2gEukPq). Bearings are inserted...