transmitter tray 3d models

Transmitter Tray HORUS X10 to print in 3D.

A simple RC transmitter tray, which can be adjusted by means of sliding holes for screws. ... Update: notches for hanging have been replaced with full holes so the tray won't fall out

Transmitter Tray Taranis Q X7 to print in 3D.

Hi guys, I wanted a transmitter tray that could fit inside case, even with a FPV screen. I printed and it work perfectly with my Graupner MX16. Print and anjoy my friends. ...Say to me if you are happy with that, please.

Latest version is Transmitter_Tray_1 A tray to hold yer 400mw transmitter from Ready Made RC. This is the second iteration, I have modified it to accept wide velcro straps instead of zip ties. See the photos for how I mounted it on top of the QAV. ...

Important: Printing of the transmitter tray including attached GCODE is optimized to the type of a printer prusa i3MK2 with the size of pad (x,y) 250x210mm. When properly transfered the attached stl files can be printed on a 3D printer with the...

Printing of the transmitter tray including attached STL is optimized to 3D printer, with the size of pad – bed (x,y) min. 200x200mm. ... The weight of the assembled tray is not higher than 250 g.  (Infill percentage = 13-15%, primary layer hight = 0,2...

Someone requested a TS5823 Version of the transmitter tray I made. So here it is. I put grippy shelf liner under the transmitter and a zip tie to on to hold it together. Inner dimensions are 27.5mm x 23mm x 6mm. Ther is a 10mm hole for the SMA...

Important: Printing of the transmitter tray including attached STL is optimized to 3D printer, with the size of pad – bed (x,y) min. 200x200mm. The weight of the assembled tray is not higher than 250 g. (Infill percentage = 15-20%, primary layer...

This is a transmitter tray with plates you can slide out to put batterys or video transmission or anything you want inside. i needed foldable neck holder to put the tray inside mallet to carry. (Sorry for bad english terms I'm using) I hope many...

I don't know if other Futaba transmitter models are similar in size for the case. My transmitter was the T10J model. I was surprised that I didn't find other similar projects from the RC Plane guys. Maybe there are some out there, and I just...

I don't like TX trays with wrist supports as I pinch and thumb the sticks depending on which aircraft I'm flying - I'm also a slope flier so the tray is ideal for solo launching large gliders. Requires 2 short lengths of 12mm OD aluminium tube...

Credit to https://www.thingiverse.com/sterling101/designs this is for the Radiomaster TX16s and similar Radios. I used two 1/4"x8" eyebolts from . ... ...

Credit to https://www.thingiverse.com/sterling101/designs this is for the Spectrum Dx6 and similar Radios. I used two 1/4"x8" eyebolts from . ... ...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/cBq7C26ca5E

Transmitter-Tray / Grundplatte_Senderpult für Futaba T8FG

Built specifically for the Nighthawk frame and the Boscam TS351 but will likely fit lots of other transmitters. I put grippy shelf liner under the transmitter and a zip tie to on to hold it together. Inner dimensions of the tray are 27.2mm X 40.5mm...

Here are my video transmitter holders for the Emax Nighthawk 250 that fit the new slim eachine video Transmitters. I created 2 models, so choose the one that orients it the way you want. One orients it LEDs up and further in, the other is further...

... slicer but didn't think to add individual files for people who's slicer may not support manipulation. Have been using the tray for a while now and it works fantastically - definitely couldn't see me using the radio without it now that's for sure!

Printing of the transmitter tray including attached STL is optimized to the type of a printer prusa i3MK2 with the size of pad (x,y) 250x210mm. When properly transfered the attached stl files can be printed on a 3D printer with the minimum size...

I wanted to desing this trasmitter holder to have something very portable as standard ones are huge. ...This one can be easely dismounted with the 4 butterfly screws and take place easely in the tramistter case from Spektrum for the IX12 (Ref : ...

After many iteration of the original design I am quite satisfied with this one. Tried to selle printed version on ebay but now I rather post it here and count on some donations to finance my printing material needs. ... I hop you will enjoy this...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/9b6Pte8BtJQ

<p>This thing was made with Tinkercad. ...Edit it online <a href="https://www.tinkercad.com/things/9b6Pte8BtJQ">https://www.tinkercad.com/things/9b6Pte8BtJQ</a></p> Category: 3D Printing

EN: Consisting of four parts that need to be screwed together. The belt linkage can be folded for transport. DE: Fast voll 3D druckbares Senderpult für Graupner MX20. Passt auch für MX16 / MX-12 ... Bestehend aus 4 Teilen die zusammengeschraubt und...

Important: Printing of the transmitter tray including attached STL is optimized to the type of a printer prusa i3MK2 with the size of pad (x,y) 250x210mm. When properly transfered the attached stl files can be printed on a 3D printer with the...

Important: Printing of the transmitter tray including attached STL is optimized to the type of a printer prusa i3MK2 with the size of pad (x,y) 250x210mm. When properly transfered the attached stl files can be printed on a 3D printer...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/cuEFDUfRdSc

<p>This thing was made with Tinkercad. ...Edit it online <a href="https://www.tinkercad.com/things/cuEFDUfRdSc">https://www.tinkercad.com/things/cuEFDUfRdSc</a></p> Category: 3D Printing

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/7sAzMg7hGiH