transmitter tray spektrum 3d models
42269 3d models found related to transmitter tray spektrum.thingiverse
I wanted to desing this trasmitter holder to have something very portable as standard ones are huge. ...This one can be easely dismounted with the 4 butterfly screws and take place easely in the tramistter case from Spektrum for the IX12 (Ref : SPM6725)
thingiverse
After many iteration of the original design I am quite satisfied with this one. Tried to selle printed version on ebay but now I rather post it here and count on some donations to finance my printing material needs. ... I hop you will enjoy this...
thingiverse
Simple wall mount for your Spektrum transmitters. Should also work with any transmitter that has a back handle. Print on side with supports and 100% infill for best strength. ...You don't want your expensive transmitters falling now ;)
thingiverse
... dx6 5 dx6i 6 Dx6e 7 dx7 8 dx8 9 dx8e 10 dx9 11 dx10 12 ix12 13 dx18 14 dx20 15 ix20 Original Design using tinker cad. ...should work on each transmitter model Buy Here : https://www.ebay.co.uk/itm/383634668670 check out my website here :www.3dcards.uk
thingiverse
These are a few critical parts I modeled From My Spectrum DXe controller for anyone who may want to make their own custom Transmitter case. For the overly complex stuff I just blocked out the shape at maximum volume so you would be able to design...
thingiverse
I wanted a way to store my transmitters away from my workspace and relatively safe up on the wall. Instructions I printed this in ABS at 250 degrees for all layers. ... Since I wasn't sure on the size...
thingiverse
Replicate of Spektrum DX9 - RC Radio Transmitter Best print it in 45 angle with support. ... Did 3D scan it with Meshroom and did get help with finish it.
thingiverse
This is a receiver tray for mounting a Spektrum AR620 receiver in an aircraft. It is form fitting and should snap in to place. ... There is an opening on the top that allows access to the bind button.
thingiverse
A replacement control stick for a Spektrum DX4e RC transmitter. Instructions Print with PLA at a slow rate. Use a minimum of 60 seconds per layer and a good part fan. ... Screw the stick in place...
thingiverse
This is a handy tray for holding an AR620 receiver. It offers some protection and makes it easy to position the receiver where you can get at the bind button without taking the plane apart. ...
thingiverse
Probably work with transmitter in same generation ( DX7 and DX8)
thingiverse
... ...Edit(17.11.2015): I added a bigger surface, so you can also put your turnigy transmitter bag on this wallmount! This transmitter bag: http://www.hobbyking.com/hobbyking/store/__40244__Turnigy_Transmitter_Bag_Carrying_Case_Red_EU_warehouse_.html
grabcad
The powerful Spektrum AirWare software in the DX8 was developed exclusively by a team of RC experts from the ground up. It includes every programming function an expert pilot could want, but you don't have to be an expert to use it. The intuitive...
thingiverse
This is completely a novelty, not really essential to enjoy the hobby but i personally prefer handling with the extra size in the transmitter wheel. ... The design is almost the same as my design Airless Tyre for Traxxas E-Revo VXL (Dual Extrusion) ...
cults3d
This is completely a novelty, not really essential to enjoy the hobby but i personally prefer handling with the extra size in the transmitter wheel. ... The design is almost the same as my design Airless Tyre for Traxxas E-Revo VXL (Dual Extrusion)...
prusaprinters
So I built a box to fit the Organge Module from HK (OrangeRX DSMX/DSM2/Devo 2.4Ghz Switchable Transmitter Module V2.0 JR/Turnigy/Taranis/Walkera compatible).Note: the box is custom made for the Orange Module 2.1. It slides in and is kept in...
thingiverse
So I built a box to fit the Organge Module from HK (OrangeRX DSMX/DSM2/Devo 2.4Ghz Switchable Transmitter Module V2.0 JR/Turnigy/Taranis/Walkera compatible). Note: the box is custom made for the Orange Module 2.1. It slides in and is kept in...
cults3d
A simple RC transmitter tray, which can be adjusted by means of sliding holes for screws. ... Update: notches for hanging have been replaced with full holes so the tray won't fall out
thingiverse
Just a wall hanger to keep things organized. ...Print in PLA without supports.
thingiverse
... But unfortunately my Spektrum DX4R Pro doesn't have a ring to connect a lanyard to. So I made one :) Just use the screw in the picture to attach the ring to your transmitter. This ring might work for other types of Spektrum transmitters to.
cults3d
This listing is for a Nifty Steering Wheel Extender for the Spektrum DX3 Transmitter - May fit other transmitters with a 55mm steering wheel as well. This little gadget allows you to drive one-handed, meaning you can keep your other hand free for...
thingiverse
Spektrum NX Series Transmitter Gimbal Stick Protectors / Magnetic fastening Modeling data is attached, so please make it well. You will need 8ea neodymium magnets 5mm in diameter and 3mm in length. ... You may need to re-adjust the holes with a...
thingiverse
This is a mount for the Spektrum 4.3 inch Video Monitor w/DVR to mount to the mighty DXe transmitter. I designed this to replace a single included mounting part, the rest of the hardware is supplied by with the SPMVM435. Other hardware you will...
thingiverse
It fits all Spektrum DX(X) transmitters. i have a DX5e, DX6, and a DX8 that it fitrs perfectly on. Comment for suggestions for improvements. I'm willing to keep this design process evolving. ... V3 edit: changed the handle cross-arm to be taller and...
thingiverse
The DX9 transmitter has an uncommon rear mounting bar which doesn't currently fit many of the existing adapters for the long range transmitter modules. ...Using just some 3/4" aluminum bars, velcro and sticky foam, you can create an adapter that keeps...
thingiverse
Latest version is Transmitter_Tray_1 A tray to hold yer 400mw transmitter from Ready Made RC. This is the second iteration, I have modified it to accept wide velcro straps instead of zip ties. See the photos for how I mounted it on top of the QAV. ...
thingiverse
Hi guys, I wanted a transmitter tray that could fit inside case, even with a FPV screen. I printed and it work perfectly with my Graupner MX16. Print and anjoy my friends. ...Say to me if you are happy with that, please.