traxxas rustler stampede spoiler 3d models

... cracked the hub responsible for holding the bearings of the rear axle. To fix it, I glued the parts back together and decided to model the broken component for others to use. ...After testing it on the street, my car performed flawlessly - hooray!

The entire system requires the full model for accurate assembly. Individual components can be referenced, but printing individual parts may result in a malfunctioning unit. ...Only the specific parts listed as printable files were designed by me and are...

... for my rear axle. Despite gluing the pieces back together, I decided it would be a good idea to design and share this part with others. I took the model for a test drive down the street and was thrilled to see that my car runs smoothly once again!

I created these 0-degree A-Arms to reduce the terrible oversteer caused by the stock 30-degree bulkhead on the Traxxas Rustler 2WD, with speedruns in mind. ... You will need: - Adjustable steering and camber links (VXL models should have this already) -...

Sturdy flexible spoiler mount for the Traxxas Sledge. ... Longer screws are needed 2x M4x28mm screws 2x M4x25mm screws 2x M4x22mm screws 2x M4 lock nut

ESC Mounting Plate for Mamba Monster X Conversion. ...Compatible with Traxxas Stampede VXL Models and Possibly More. ... You Will Need the Following Hardware to Install: Zip Ties 2 x 18 mm Hex Cap Screws 2 m3 Locknuts

I created these 0-degree A-Arms to reduce the terrible oversteer caused by the stock 30-degree bulkhead on the Traxxas Rustler 2WD, with speedruns in mind. You will need: Adjustable steering and camber links (VXL models should have this already) Very...

This traxxas rustler 4X4 rear sub carriers work just fine, with a bit of sanding.

ESC mount plate for a Hobbywing EZRUN MAX 10. ...Fits Traxxas Stampede VXL models and possibly more. ...For strength, it is better to use double-sided tape You will need the following hardware for installation: 2 x 16 mm hex cap screws

Wypełnienie 100% Pasuje do modelu Traxxas Rustler VXL 4x4 Uchwyt montowany na tylnej części mocowania obudowy na 4 oryginalne śrubki

This creation is proudly crafted with Tinkercad, a fantastic tool that lets you edit and refine your designs right within the browser - check out the link at https://www.tinkercad.com/things/k5m6rBc7CkO.

Eight people require a total of thirty-two thousand three hundred sixty 3M sixteen-thread screws.

I designed this 3D printed temporary upgrade that call Front hinge pin brace for the traxxas rustler or slash 2wd. I designed this brace to fill in the space in the STRC Front hinge pin in the Front bulkhead Suspension Hinge Pins Traxxas 2wd rustler...

Traxxas Stampede 2wd lcg chassis (Work-In-Progress)Designed in AutoCAD, this is to make the chassis of the Traxxas Stampede more closer to the ground for rc track racing and taking jumps easier. ...Can also be used for other events such as drag racing...

Fits Traxxas Stampede VXL models and possibly more. For strength, it is better to use double-sided tape. I have a 120A version, I added a model with a button under 80A, but did not print it. As I saw from the pictures, they differ in the size of the...

It does flex very well and can hold the weight of the car well, although I cannot promise the spoiler / wing legs will hold the full weight in a straight up and down because of the print position. The wing / spoiler is held on by one screw in each...

It does flex very well and can hold the weight of the car well, although I cannot promise the spoiler / wing legs will hold the full weight in a straight up and down because of the print position. The wing / spoiler is held on by one screw in each...

This is for a traxxas stampede 2x4 but might work on a 4x4 this is press fit and will not need any hardware. ... Designed for a 3s 11.1v Lipo

I will add more as I can.Current Versions Count Available:  4Had to remove a few as a design flaw with screw holes effected all models.Print Settings:PLA PRO -InlandExtrude Temp - 215cFirst Layer Hight - .32All other layers - .20Infill -...

This is a redesign of bobcatfr63, I was getting a bad scraping noise with the spring rubbing the sides of the shield. I shrunk down the front and also made it a bit larger to cover more of the spring. This object was made in Tinkercad. ...Edit it...

Designed as the culmination task in the CAD course.

Customizes standard battery tray to accommodate larger power source \ fits snugly beneath electronic speed controller.

I Decided To Create An Extension For My Broken Antenna Support Straw Thing Using Onshape. ...The Project Is Available Here: Https://Goo.Gl/Rsdspj.

A project for a CAD cource at UW-Stout a few years ago. ...Not entirely complete because I ran out of time.

Need a Holder for the 3S 5000 Lipo Akku, Original was only for a 22mm Akkus,The new one has 35mm so I have to buld my own one.

Customized version of https://www.thingiverse.com/thing:4381135 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4381135

A mounting solution for the Hobbywing Max10 SCT in a Traxxas Stampede 4x4 with the stock chassis. This design has 3 parts; a base plate, a step (to keep things level) and then a holder that keeps the ESC and switch in place. ... 2 x M3 6mm (into ESC) ...

Battery strap for Traxxas 2WD Stampede. I added a retaining clip to hold the wires and balance lead so they don't flop around. ...There are 2 files - one has a spacer underneath for thinner batteries and another without a spacer