traxxas slash 2wd gearing 3d models

This is a 70 tooth Traxxas Slash 2wd spur gear, similar to part 4370. I have not yet tried with my 550 motor because the 76 tooth spur/ 23 tooth pinion combo provides a nice balance of acceleration and speed without melting my 550 brushed OOB...

This is a Traxxas Slash 2WD 1/10 model 64t (64 teeth) spur gear. I plan to use it with the 28 tooth pinion gear I just posted. It will not work with the 23 tooth pinion or lesser toothed pinion gears because it is smaller. This is not based on any...

This is a 73t 46p spur gear for Traxxas Slash 2WD. It should work with a 23 tooth pinion or larger. I never used it yet so please leave me a comment or like if this works. ...Thanks!

This is a 46p 67t (67 teeth) spur gear I made for my Traxxas Slash 2WD 1/10. It's probably the fewest teeth on a spur gear that will work in combination with a 23 pinion gear. This baby zooms on my RC, but you really need to ease into the throttle...

Printed for a Traxxas Slash 2wd. (The 4x4 setup is different) This one doesn't use bushings or bearings, so it might wear out quickly. Seems to hold up pretty well though. Thanks, Enjoy! ...

I adjusted the size to fit a 2wd Slash. The fit might be a little tight, but over time, it will break in. ...Fill at 100% to ensure strength.

All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm screws....

All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm...

This is a simple flat ESC Mount that fits in the stock ESC location on the stock Traxxas Slash 2WD Chassis and the LCG Chassis. It might fit other models that use the XL-5 ESC because that's what these holes line up with. The plate is 55mm x 55mm. I...

This is an experiment to extend the wheelbase of a Traxxas Slash 2WD to fit Arrma Infraction or Felony bodies. It makes the wheelbase 76 millimeters (3 inches) longer than stock. It is designed around the Slash LCG chassis, and I have no idea if it...

This is a simple wheelie bar I designed for my Traxxas Slash 2wd VXL, as it was spending far too much time on it's roof! In addition to the printed parts you will need the following parts - 2x 625 bearings 2x M5x20 countersunk head bolts 2x...

This is the first of many print sets for a 2wd Slash down-force system. Suitable for both drift and drag cars. When the whole system is installed your car should pull itself down and make the car squat as speed increases. This fits with and without...

front part for traxxas slash 2WD

traxxas slash 2wd rear bumper mount compatible with asciencepotato's 4wd bumper. ...It's a little fragile, so please drive carefully.

I designed these mud guards for a Traxxas Slash 2wd High center of gravity chassis to keep the dirt out of the chassis. It uses the holes from the nerf bars so you will need 4 screws that are a bit longer to replace the ones from the nerf bars. ... ...

This is a Traxxas Slash 2wd LCG Chassis - Sidewinder SCT ESC Holder Bracket and FS-RG3E Receiver Holder. The Castle Sidewinder 3 SCT with phan will need 2 - 3x25mm to hold it in place. ... The FLYSKY FS-RG3E will need one 3x12mm and a little shoe...

This is designed for a traxxas slash 2wd it allows you to mount the transmission backwards for better centre of gravity and cornering ability but you can also mount it stock. ...this was designed to be cut out of aluminium but can also be laser cut out...

Maybe it can fit on the other 2wd Traxxas as well with some modifications. It is based on the new style of clip on straps presented on the Traxxas 4TEC 2.0 and TRX4. The only modification required to the car is enlarging the hole where the hexagonal...

Maybe it can fit on the other 2wd Traxxas as well with some modifications. It is based on the new style of clip on straps presented on the Traxxas 4TEC 2.0 and TRX4. The only modification required to the car is enlarging the hole where the hexagonal...

Body Mount Extension as Add-On to the original Body Mount of the Slash 2WD to fit the Proline F150 1979 body in the front. ... Built with Tinkercad.

wheelie bar for traxxas drag slash use m3x16mm screws these could be used for show or as templates to fit bodies

This is a very simple chassis saver I designed for my Traxxas Slash 2wd with High Centre of Gravity chassis. Proline used to make these a few years ago to eliminate the weak spot where the transmission bolts to the chassis. Unfortunately, when...

This is the Front Caster Block for a Traxxas Slash 2WD, Bandit or Rusler. Print them if you break one...  PLA Holds up ok in mid Temp and Cold.  I PLA  is fine for normal racing conditions. I raced for 1 hour accident free with oit breakage. They...

I made this 0 degree bulkhead to make my slash into a drag car. Works great! ...Print flat with supports touching buildplate for best results!

These are some simple spacers to raise the body mounts on a 2WD Traxxas Slash to accept a Ford Raptor body. ...Learn more about the process at www.RCDetails.ca!

These are some simple spacers to raise the body mounts on a 2WD Traxxas Slash to accept a Ford Raptor body. ... Learn more about the process at www.RCDetails.ca!

I designed this brace to fill in the space in the STRC Front hinge pin in the Front bulkhead Suspension Hinge Pins Traxxas 2wd rustler and slash this is to be used for a temporary part until it can be replaced with aluminum brace. if you wish to...

Traxxas Slash 2wd Body Mounts 18mm 20mm Support is optional to print smoother circular body holder section, raft can be also used to stabilize prints. I used this on my RJ Speed Late Model Stock body, body needs to be lowered, original body...

and it must be a traxxas 2wd slash LCG or HCG you may need double-sided tape depending upon what you did to your chassis but in my case there was no need for me to do that because it fits tightly and I would not worry about it falling off. ...So enjoy...

I designed this 3D printed upgrade that I call Mount for Anything for traxxas slash 2wd LCG m2. So I designed this 3D printed component for the purpose of laying a mount so one can put on a gyro or light system or anything else. This 3D printed...