traxxas slash 4x4 chassis 3d models

Compatible with Rustler 4x4 or Slash 4x4 equipped with a Chassis Brace Recommended Traxxas LED light kit with the Accessory Power Supply 3v...

This is a 40mm x 40mm flat plate used to mount anything to the front area of a slash 4x4 LCG chassis. The plate is 4mm thick and can be mounted to the chassis with 2 M3 x 6mm button head screws (TRA 2575). I am using the plate to hold a GNSS...

This is an extended battery hold-down for the traxxas Slash 4x4 LCG chassis. ...I designed it to work with my Turnigy Rapid 5500 mah 4S LiPo battery (as you can see in the pictures)Be aware that for this to fit the aforementioned battery you would need...

For the Traxxas Slash 4X4 LCG Chassis: A means had to be found to secure the Castle Creations Mamba-X ESC to the Traxxas Slash 4X4 LCG and relocate the Receiver. I plan to use a chassis brace so relocation of the receiver to the front center of the...

This innovative two-part design features a main holder and clamp that utilize existing mounting holes on the Traxxas Slash 4X4's chassis, eliminating the need for any drilling. The main holder has a dedicated compartment for the Castle Creations...

RC Stand for Traxxas Slash 4x4. Included are both HCG & LCG Chassis Stands. HCG is still a work in progress. LCG is complete and the bay has room for the Traxxas EZ Peak+ ID Charger. ...I had previously uploaded this with logos but had to remove them.

RC Stand for Traxxas Slash 4x4. Included are both HCG & LCG Chassis Stands. HCG is still a work in progress. LCG is complete and the bay has room for the Traxxas EZ Peak+ ID Charger. Support are required for the front opening. Supports for...

GoPro style mount designed to bolt to the chassis of a Traxxas Slash 4X4 (Not sure on 2WD) with recess under the mount to allow for a chassis protector / dust cover.

This is a cover for the Traxxas Slash Low Center of Gravity chassis. ...You can print it without any supporting structures.

This is a component to fasten a thicker rechargeable battery (25 mm high, eg. ...LiPo Pack 5000mAh) in the TRAXXAS Slash 4x4. You can use the original bow to push it into the component. Please notice: you have to unscrew the stud a little bit. ...

This is a customized Drift wheel designed specifically for my 4x4 Traxxas Slash. I've been eager to try out drifting and didn't want to purchase an entirely new vehicle. I fabricated the face flush for hassle-free printing. Additionally, I created...

This design is for use with 12mm hexes, which the Slash 4x4 comes stock with. These should also fit in the rear of 2wd Slash models. I printed these in PLA with .25 layer height with only 2 walls and 10% infill. I tested them out on somewhat rough...

Human: Roll cage I designed specifically for the Slash 4x4 truck mounts directly to the body mounts' attachment holes on the vehicle. The roll cage has only been printed once using Hatchbox Blue PLA, and it hasn't undergone any rigorous testing...

Chose to swap out the foam insert in the battery holder since the fresh lithium-polymer cells I had been using were noticeably shorter than the original Traxxas batteries.

Internal-splined half shaft for Traxxas Slash 4x4.MODEL# 6853A.

It's the measurement from the original part. ... Internal-splined half shaft for Traxxas Slash 4x4. ... MODEL# 6853A.

I crafted the Traxxas Slash 4x4 extended body mounts initially, and upon further investigation, discovered that fabricating spacers for the body mount bracket imparts significantly greater strength than the mounts I 3D printed.\r\nThese spacers...

Adapter plate to mount any esc to a traxxas Slash 4x4. ...Use double side tape to glue the ESC to the plate.

The left front/rear arm is required for my Traxxas Slash 4x4 vehicle, as both the front and rear arms on this model are identical in design.

Mount a Traxxas Slash 4x4 Esc Mounting Plate on Any Vehicle. ...Attach Double-Sided Tape Directly to the Esc, Secure it Firmly in Place on the Plate.

Designed in AutoCAD, this allows for dual motors on a Traxxas Slash 4x4. This been tested in ABS and I've printed them on a Tevo Tornado 3D printer. ...Some filing may be required for perfect fit.

Purchased a brand-new, pre-finished body for my Traxxas Slash 4x4 but it failed to fit properly, prompting me to modify the height of the body mounts instead. ...Following several design iterations, I ultimately settled on three distinct dimensions that...

These custom side rails were specifically designed for use with the Traxxas Slash 4x4 LCG chassis paired with J-concepts' 2238 overtray. Rock debris used to enter under the overtray and into the space above nerf bars, causing frustration, but these...

I designed a stand specifically for my son's Traxxas Slash 4x4 1:10 scale vehicle so he could store it safely with the wheels off the ground. This setup is allegedly crucial in maintaining the round shape of the wheels and preserving the shocks and...

I've designed a custom 3D printed switch mount for my Traxxas Slash 4x4 HCG, specifically to house the brushless motor system's switch. Since it needs to be installed somewhere, I'm providing this file with installation details. To download and...

...I lost the gear cover of my Traxxas Slash 4x4 LCG... :(</p> <p>So I designed my own. It's nearly as perfect as the original piece... but different...</p> <p>Several testprints &amp; model iterations later, I had something that fits ok :)</p>...

This is a control arm I modeled for a Traxxas rustler or slash 4x4. I believe it is also compatible with a rear 2wd but I haven't tested. Print horizontally, and make sure supports are on. Mirror horizontally in slicer to make a right arm. STANDARD...

I managed to lose the gear cover of my Traxxas Slash 4x4 LCG, which was a real bummer :(. So I came up with my own design. It's nearly as perfect as the original piece, but it has its own unique touches. After several test prints and model...

30mm fan mount for slash 4x4 slipper clutch. ... Goes on the right side of the vehicle mounts on upper right engine mount.

The imbalance between the front and rear of the Traxxas Slash 4x4's original body was a major issue that required attention. I modified leftover parts from the stock body mount using extension body posts, cutting them down to size to raise the front...