traxxas slash 4x4 front bumper 3d models

I was searching for a front bumper for my Backslash project that resembled the front bumper of a losi 8ight... when my search came up short I decided to create my own. ... Very nice fit, designed it to fit and snug as possible and all screw holes were...

Printed this Part in Flex PLA Turns out to be slightly softer than the original but unbreakable with good dampening. Only needs support at the horizontal screw-holes. I solved this via "support enforcer" option in my slic3r software. Survived...

a front bumper for the traxxas slash 1/10 scale 4x4 RC car uses the mount from the RPM aftermarket front bumper. ...has holes for 10 LEDs

After several hours of measuring and designing, followed by four test prints along the way, I came up with the new front bumper bar for the 1:10 scale Traxxas Slash 2wd. It uses the original screws and mounting position. I feel that it is not as...

EDIT: updated with newer design a front bumper for the traxxas slash 1/10 scale 4x4 RC car. ...with 10 holes for LEDs this uses the mounts for the RPM aftermarket front bumper mount. Print instructionsUnassociated tags: front bumper, LED bar, LED mount,...

EDIT: updated with newer design a front bumper for the traxxas slash 1/10 scale 4x4 RC car. ...with 10 holes for LEDs this uses the mounts for the RPM aftermarket front bumper mount.

SummaryEDIT: updated with newer design a front bumper for the traxxas slash 1/10 scale 4x4 RC car. ...with 10 holes for LEDs this uses the mounts for the RPM aftermarket front bumper mount.

... tires. ...uses the stock mounting holes on the pan and the bumper but you will need to get another set of hardware and tap the holes in the riser. ...You will no longer use all 4 of the lower mounting holes where the bumper attaches to the chassis.

for backslash

RC Stand for Traxxas Slash 4x4. Included are both HCG & LCG Chassis Stands. HCG is still a work in progress. LCG is complete and the bay has room for the Traxxas EZ Peak+ ID Charger. Support are required for the front opening. Supports for hexagons...

Here is a Traxxas Slash 4x4 front and rear 5mm LED light bar for your RC. I print it with PETG and Nylon filament and 100% infill with no support. I have two versions of the Front Light Bar the first one is light weight and the second one is beefier....

RC Stand for Traxxas Slash 4x4. Included are both HCG & LCG Chassis Stands. HCG is still a work in progress. LCG is complete and the bay has room for the Traxxas EZ Peak+ ID Charger. ...I had previously uploaded this with logos but had to remove them.

This is a 40mm x 40mm flat plate used to mount anything to the front area of a slash 4x4 LCG chassis. The plate is 4mm thick and can be mounted to the chassis with 2 M3 x 6mm button head screws (TRA 2575). I am using the plate to hold a GNSS...

This body mount extender screws on to your Traxxas front suspension for to accommodate larger wheels and tires. This extender does not require supports. ...Part took 20-25 mins to print.

This is a simple project i made for my Traxxas Slash to mount the lights. RPM bumpers are required (won't fit in original bumpers). ... Here is the link for LEDs used in this project: ...

the 2 holes in the middle of the part are for attaching an additional center brace for extra support.brace for mounting between the bumper armshttps://www.youmagine.com/designs/traxxas-slash-bumper-arm-bracerear bumper...

EDIT: part has been updated with tighter dimensionsa rear bumper for the 1/10 scale traxxas slashbumper arms can be found here https://www.youmagine.com/designs/traxxas-slash-bumper-arm-bracesupport brace for the rear bumper...

EDIT: updated with newer design a rear bumper for the 1/10 scale traxxas slash use with my printable bumper arm http://www.thingiverse.com/thing:1175688 and printable bumper arm brace for extra support http://www.thingiverse.com/thing:1175687

SummaryEDIT: updated with newer design a rear bumper for the 1/10 scale traxxas slash use with my printable bumper arm http://www.thingiverse.com/thing:1175688 and printable bumper arm brace for extra support http://www.thingiverse.com/thing:1175687

SummaryEDIT: updated with newer design a bumper arm for the 1/10 scale traxxas slash. the 2 holes in the middle of the part are for attaching an additional center brace for extra support. ...use with my printable bumper...

EDIT: updated with newer design a rear bumper for the 1/10 scale traxxas slash use with my printable bumper arm http://www.thingiverse.com/thing:1175688 and printable bumper arm brace for extra support http://www.thingiverse.com/thing:1175687 Print...

the 2 holes in the middle of the part are for attaching an additional center brace for extra support. use with my printable bumper http://www.thingiverse.com/thing:1175690 use with my printable bumper arm brace for extra support...

EDIT: updated with newer design a bumper arm for the 1/10 scale traxxas slash. the 2 holes in the middle of the part are for attaching an additional center brace for extra support. ...use with my printable bumperhttp://www.thingiverse.com/thing:1175690...

GoPro style mount designed to bolt to the chassis of a Traxxas Slash 4X4 (Not sure on 2WD) with recess under the mount to allow for a chassis protector / dust cover.

This is a component to fasten a thicker rechargeable battery (25 mm high, eg. ...LiPo Pack 5000mAh) in the TRAXXAS Slash 4x4. You can use the original bow to push it into the component. Please notice: you have to unscrew the stud a little bit. ...

Designed to adapt Revo style bumper to the Traxxas 4x4 chassis. ...Fits to the front diff housing.

This is a Drift wheel I created for my 4x4 Traxxas Slash. I've been wanting to mess around with drifting, and really didn't want a whole new vehicle. I made the face flush for easy printing. I also added a version with a 17mm hex, for those silly...

This is a Cover for Traxxas Slash LCG Chassi. You can print without support. ...

These spacers that I have designed for my Traxxas Slash 4x4 for the purpose of Providing some spacing between the RPM rear bumper and the RPM mud flaps. The reason that I have design these spacers is because my Traxxas Slash 4x4 will not pop wheelies...

bumper mounts for the traxxas slash 1/10 scale 4x4 RC car