traxxas slash light bar 3d models
294844 3d models found related to traxxas slash light bar.thingiverse
Here is a Traxxas Slash 4x4 front and rear 5mm LED light bar for your RC. I print it with PETG and Nylon filament and 100% infill with no support. I have two versions of the Front Light Bar the first one is light weight and the second one is beefier....
thingiverse
Burnout bar to use on a Traxxas Slash based No Prep car. Fits a standard RPM style Wheelie bar mount and depending on your body, should be completely hidden underneath. I used this mount and designed this Burnout Bar to fit it perfectly.
thingiverse
... a V2 with more meat (it broke where it thins out). Should fit just as well as the first. Again, put the first set of c-clips on, the push the pins through the tie bar and through the bulkhead, put the other c-clips on from the rear... ...
thingiverse
This is a simple wheelie bar I designed for my Traxxas Slash 2wd VXL, as it was spending far too much time on it's roof! In addition to the printed parts you will need the following parts - 2x 625 bearings 2x M5x20 countersunk head bolts 2x...
cults3d
wheelie bar for traxxas drag slash use m3x16mm screws these could be used for show or as templates to fit bodies
thingiverse
This is a remix of the light bar for RPM bumper. ...My LEDs were too small for the original so I created a whole new one using the dimensions from the original.
thingiverse
This is for a traxxas slash being used for a wide body circle track.
thingiverse
Battery retention bar/strap for a variety of RTR Traxxas vehicles (Rustler, Stampede, Slash). This is a remix of my strap for vintage racing vehicles. Not much to say here as there are a bunch of these out there on Thingiverse. I created this one...
prusaprinters
Lightbar cover for traxxas 3791 light bar. Printed in TPU it snuggly covers the lightbar and has a KC light style look to it.
thingiverse
for slash and rustler only, you need to take off the plastic spring on the front bumper and bolt the light bar on the holes in the bumper.
pinshape
for slash and rustler only, you need to take off the plastic spring on the front bumper and bolt the light bar on the holes in the bumper.
thingiverse
This is a light bar for a Traxxas Nitro Sport. It may work on other R/C cars, but I don't know. It uses 18 3/16" in diameter LEDs. I got mine out of a free Harbor Frieght flashlight. Have fun! I will be adding new files for the newer Harbor...
thingiverse
Light bar made to screw to the front of the TRX4 Sport roof rack (remove the bar at the front). Simply stick 100mm length of LED strip to the front above the step. Holes either side will generally need drilling out to 2mm. ... Note this is pretty...
thingiverse
I designed these light pods to attach to a stock Traxxas Slash bumper. To install, drill a hole in the bumper and thread an M3 screw through the hole in the bracket and into the bumper. Then stick the LEDs into the other hole. I used some random 5mm...
thingiverse
Traxxas SLASH RC truck roll bars. These are cosmetic and really improves the look of the truck. ...I fastened them to the body by drilling holes and using little screws.
thingiverse
This is a front bumper mounted LED light bar for the Traxxas TRX4 Sport, though it is pretty much universal so it should fit just about any truck. The light bar is designed in two parts, the clear lens and the housing. The two parts sandwich one...
prusaprinters
Designed from scratch based on pictures I saw online, this LED light bar goes on top of the Rollbar I made for the TRX4. ...Screws on with 2 M2 screws.</p>
thingiverse
... of the system, basically acting as a breakaway as to not damage the main part. You will need 2 flags (any type really), some M3 hardware (socket head screws and simple nuts), and it fits on a classic Traxxas brand wheelie bar. ...Hope you like it!
thingiverse
My Traxxas Slash 4x4 was the only car in my model-garage without light. Even this is a very fast Basher for rough use - and I am using em like a hardcore basher - I thought, it should have some lights on it. This is why I designed the lights super...
thingiverse
As the the mounting points of the rear sway bar are not good enough (IMHO) I designed a holder which seem to function perfect and is easy to install and print. I used M3x16 screws to mount the holder and the shock tower to the body. For the sway bar...
thingiverse
Here is another version of the front bumper for the Traxxas Maxx. ... It is split into 2 parts: The bumper. The light bar.
myminifactory
This is a curved light bar designed to directly fit onto the Expedition Rack accessory for the Traxxas TRX-4 Sport body. The light bar mounts using the two provided screw holes on the rack and follows the curve of the top bar. Print the housing in...
prusaprinters
I desinged a roof light bar for my Traxxas summit 1/10 It replaces the original fake light bar, no modifications needed. I wired the front lights in a series connection so 6V from the reciever would not be to much volts. 5...
thingiverse
... Maxx rc truck. ... It is split into 2 parts: - The bumper. - The light bar. There are 2 bumper options: - One with our name on it - One with just our logo. ... They were made on the Makerbot Sketch, not the replicator as listed below.