traxxas slash rear bumper 3d models

EDIT: part has been updated with tighter dimensionsa rear bumper for the 1/10 scale traxxas slashbumper arms can be found here https://www.youmagine.com/designs/traxxas-slash-bumper-arm-bracesupport brace for the rear bumper...

these are the 2 pieces that make up the rear bumper mount on the traxxas slash 1/10 scale 4x4 R/C car. I've included a hitch mount on the top piece as well. Print instructionsUnassociated tags: bumper mount, R/C, slash bumper, traxxas slash Category:...

bumper mounts for the traxxas slash 1/10 scale 4x4 RC car

these are the 2 pieces that make up the rear bumper mount on the traxxas slash 1/10 scale 4x4 R/C car. ...I've included a hitch mount on the top piece as well.

traxxas slash 2wd rear bumper mount compatible with asciencepotato's 4wd bumper. ...It's a little fragile, so please drive carefully.

This is a 3D printed license plate with its holder that I have designed for my Traxxas 2wd slash RPM rear bumper this is a cosmetic upgrade to make this RC vehicle look more unique. if you wish to download this file the photos will show you how to...

This part I have redesign for my Traxxas Slash 4 by 4 because I have a better computer and the software to go with it this component is a revision of the original design that is currently in my Traxxas Slash two wheel drive if you wish to download...

This is a simple project i made for my Traxxas Slash to mount the lights. RPM bumpers are required (won't fit in original bumpers). ... Here is the link for LEDs used in this project: ...

So I designed these Real or Fake Rear Lights for the RPM Rear Bumper that is used on a Traxxas Slash vehicle if you wish to download this file you will need about four screws they need to be at least a minimum of 3x20mm also you will need some...

These spacers that I have designed for my Traxxas Slash 4x4 for the purpose of Providing some spacing between the RPM rear bumper and the RPM mud flaps. The reason that I have design these spacers is because my Traxxas Slash 4x4 will not pop wheelies...

This is a cosmetic upgrade that i designed for the RPM Rear Bumper of a 2wd or 4w slash for cosmetic looks to make the RC vehicle look unique. The taillights are nonfunctioning there just looks. ...What you will need to install them you will need to get...

the 2 holes in the middle of the part are for attaching an additional center brace for extra support.brace for mounting between the bumper armshttps://www.youmagine.com/designs/traxxas-slash-bumper-arm-bracerear bumper...

not necessary but improves strength.mounts between the 2 bumper arms giving extra supportmy printable bumper arms can be found here https://www.youmagine.com/designs/traxxas-slash-bumper-armthe bumper here...

SummaryEDIT: updated with newer design a rear bumper for the 1/10 scale traxxas slash use with my printable bumper arm http://www.thingiverse.com/thing:1175688 and printable bumper arm brace for extra support http://www.thingiverse.com/thing:1175687

EDIT: updated with newer design a rear bumper for the 1/10 scale traxxas slash use with my printable bumper arm http://www.thingiverse.com/thing:1175688 and printable bumper arm brace for extra support http://www.thingiverse.com/thing:1175687

EDIT: updated with newer design a rear bumper for the 1/10 scale traxxas slash use with my printable bumper arm http://www.thingiverse.com/thing:1175688 and printable bumper arm brace for extra support http://www.thingiverse.com/thing:1175687 Print...

a front bumper for the traxxas slash 1/10 scale 4x4 RC car uses the mount from the RPM aftermarket front bumper. ...has holes for 10 LEDs

SummaryEDIT: updated with newer design a bumper arm for the 1/10 scale traxxas slash. the 2 holes in the middle of the part are for attaching an additional center brace for extra support. ...use with my printable bumper...

the 2 holes in the middle of the part are for attaching an additional center brace for extra support. use with my printable bumper http://www.thingiverse.com/thing:1175690 use with my printable bumper arm brace for extra support...

EDIT: updated with newer design a bumper arm for the 1/10 scale traxxas slash. the 2 holes in the middle of the part are for attaching an additional center brace for extra support. ...use with my printable bumperhttp://www.thingiverse.com/thing:1175690...

After several hours of measuring and designing, followed by four test prints along the way, I came up with the new front bumper bar for the 1:10 scale Traxxas Slash 2wd. It uses the original screws and mounting position. I feel that it is not as...

EDIT: updated with newer design rear carrier for the 1/10 scale 4x4 traxxas slash

SummaryEDIT: updated with newer design rear carrier for the 1/10 scale 4x4 traxxas slash

EDIT: model has been updated with tighter dimensionsrear carrier for the 1/10 scale 4x4 traxxas slash

Here is a reasr bumper for the Traxxas Maxx rc truck to match the front bumper.

Designed to adapt Revo style bumper to the Traxxas 4x4 chassis. Fits to the rear diff housing. It currently lacks a mount for the swaybars. ...My intent is to put Summit bumpers on a Telluride and I don't see the need for sways.

I didn't care for the chrome bumpers on my TRX4 Bronco and I couldn't find a rear bumper I liked on Thingiverse. This is what I created to replace my chrome bumper. ... I don't recall what infill I printed it at as I printed it a month or so ago.

Wanted a bumper for my TRX-4 with a Axial Cherokee body on it that would fit in tight to the rear of the vehicle and not hang down very low. I used a bumper mount with very little drop and as far out on the frame as I could get. Added a spare tire...

Traxxas slash rear body brace

... for the traxxas slash 1/10 scale 4x4 RC car. ...with 10 holes for LEDs this uses the mounts for the RPM aftermarket front bumper mount. Print instructionsUnassociated tags: front bumper, LED bar, LED mount, R/C, traxxas slash Category: R/C Vehicles