traxxas slash with castle brushless 3d models
2730472 3d models found related to traxxas slash with castle brushless.thingiverse
Mount for the Castle Creations Sidewinder SCT within a Traxxas Rally/Slash with a LCG chassis. There is a ziptie holder on the far end of the switch to hold the motor wires in place as well. You'll need one M3x8mm and M3x12mm cap head screw for...
thingiverse
It has mounting holes to fit onto the Traxxas Slash 2WD stock chassis as well as the 2WD LCG chassis. It also has a mount where you can put the switch with skinny cut outs to tuck the wires underneath. There are tiny holes for screws to mount the...
prusaprinters
Mount for the Castle Creations Sidewinder SCT within a Traxxas Rally/Slash with a LCG chassis. There a ziptie holder on the far end of the switch to hold the motor wires in place as well.</p> <p>You'll need one M3x8mm and M3x12mm cap head screw for...
thingiverse
This part I have redesign for my Traxxas Slash 4 by 4 because I have a better computer and the software to go with it this component is a revision of the original design that is currently in my Traxxas Slash two wheel drive if you wish to download...
thingiverse
EDIT: updated with newer design rear carrier for the 1/10 scale 4x4 traxxas slash
pinshape
SummaryEDIT: updated with newer design rear carrier for the 1/10 scale 4x4 traxxas slash
thingiverse
This contains a Traxxas 46p 76-tooth spur gear (among others and pinions) which I use for my Slash 2WD RC car. It is a high quality and accurately measured 20th generation design which I am currently racing with, and it prints well even on my...
youmagine
the lower shock spring support for the suspension on the 1/10 scale traxxas slash.version of this with an integrated guard platehttps://www.youmagine.com/designs/traxxas-slash-shock-guard-81b09451-49bd-4154-8d65-b13669b0461c
youmagine
EDIT: model has been updated with tighter dimensionsrear carrier for the 1/10 scale 4x4 traxxas slash
youmagine
EDIT: updated with newer designa bumper arm for the 1/10 scale traxxas slash. ...the 2 holes in the middle of the part are for attaching an additional center brace for extra support.brace for mounting between the bumper...
youmagine
EDIT: part has been updated with tighter dimensionsa rear bumper for the 1/10 scale traxxas slashbumper arms can be found here https://www.youmagine.com/designs/traxxas-slash-bumper-arm-bracesupport brace for the rear bumper...
youmagine
EDIT: model has been updated with tighter dimensionsfront steering block for the traxxas slash 1/10 scale 4x4 RC car. ...bearings fit perfectly
thingiverse
the lower shock spring support for the suspension on the 1/10 scale traxxas slash. ...version with shieldhttp://www.thingiverse.com/thing:1175692
thingiverse
the front to the traxxas slash 2wd model. ...i haven't printed it yet so please tell me if it works Instructions print with 100% infill
youmagine
this is a lower spring support for the suspension with a shock guard added to it, it fits the stock springs, not sure about big bores.version with a shorter shieldhttps://www.youmagine.com/designs/traxxas-slash-shock-support-and-guard-shortversion...
youmagine
this is the traxxas slash 1/10 scale battery adapter post. ...fits fine in the chassis.
thingiverse
this is the traxxas slash 1/10 scale battery adapter post. ...fits fine in the chassis.
thingiverse
This is just a fun decorative addition to my Traxxas Slash. Instructions Print both pieces with 100% infill with no rafts or supports. ...Place pieces on the front bumper and hot glue together.
thingiverse
RC Stand for Traxxas Slash 4x4. Included are both HCG & LCG Chassis Stands. HCG is still a work in progress. LCG is complete and the bay has room for the Traxxas EZ Peak+ ID Charger. ...I had previously uploaded this with logos but had to remove them.
thingiverse
RC Stand for Traxxas Slash 4x4. Included are both HCG & LCG Chassis Stands. HCG is still a work in progress. LCG is complete and the bay has room for the Traxxas EZ Peak+ ID Charger. Support are required for the front opening. Supports for...
prusaprinters
the 2 holes in the middle of the part are for attaching an additional center brace for extra support. use with my printable bumper http://www.thingiverse.com/thing:1175690 use with my printable bumper arm brace for extra support...
prusaprinters
EDIT: updated with newer design a rear bumper for the 1/10 scale traxxas slash use with my printable bumper arm http://www.thingiverse.com/thing:1175688 and printable bumper arm brace for extra support http://www.thingiverse.com/thing:1175687 Print...
thingiverse
EDIT: updated with newer design a bumper arm for the 1/10 scale traxxas slash. the 2 holes in the middle of the part are for attaching an additional center brace for extra support. ...use with my printable bumperhttp://www.thingiverse.com/thing:1175690...
pinshape
SummaryEDIT: updated with newer design a bumper arm for the 1/10 scale traxxas slash. the 2 holes in the middle of the part are for attaching an additional center brace for extra support. ...use with my printable bumper...
thingiverse
EDIT: updated with newer design a rear bumper for the 1/10 scale traxxas slash use with my printable bumper arm http://www.thingiverse.com/thing:1175688 and printable bumper arm brace for extra support http://www.thingiverse.com/thing:1175687