tree house model

Tolerences are tight on this model and will require percussive pursuasion to fit a 2020 bar Base - print with inside pointing up, support the central overhang, the Ports section print as bridged ### PETG: Top- print with the inside pointing up, this...

Print Settings: Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: No Resolution: .15 or .2 Infill: 50% Notes: Tolerances may vary. Please direct message me if you're having trouble in either direction (too weak or too stiff). A...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_rotation = 0 custom_top_port_corner_resolution = 8 custom_right_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

I recommend scaling the models 101%-103% if you plan to mix ABS and PLA. Note 2: My RH hotend is all metal. Printing above 230C with a PTFE lined hotend isn't usually recommended. How I Designed This I ended up making five different iterations...

Both, YES at the same time; 0.20 Resolution on the finest scale and that too all combined to get desired model. Once everything had adhered, using my favorite...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Another thing to note is that there have been a few minor changes to the model since I printed the one in the pic, however I don't think anything changed will cause a problem. The STP file is included for remixing. Just wanted to mention some info...

We successfully engineered an incredibly stable and secure mounting arrangement by adjusting the RC roof rack's structural reinforcement through computer-aided engineering models. By applying advanced design methodologies, our innovative product not...

Printing Instructions for 'A' Category (applies to all A models): I wanted heavier feeling pistols so I went with a 50% infill--this can easily be scaled back to save on filament, so feel free to go down to 20% if you'd like. Print facing down...

This model will do the same stuttering if printed too fast even with the used a reduced segment count (50) in the cylinders. The trusty SD card worked for me with a big batch of these. The other solution was to slow the print down.Let me know in...

The conditions to use those files are : - print it for YOUR OWN USE ONLY (no sales) - Keep the EZ-TRIM name on the model and use EZ-TRIM name in your communication on the concept. In the association Windsurf EZ-TRIM Group , we have set a...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

Orient the model on the flat surface in PrusaSlicer then paint supports on the lower edges of the camera shroud. Set supports for enforcers only.AssemblyThe Raspberry Pi 4 (I used a 4GB) and camera V2 are held in place with a couple of screws each. ...

While it worked OK for most things, there came a time when I was trying to print a model with steeply overhanging points and the stock cooling just wouldn't cut it. I designed this adapter to allow a standard 5015 radial fan (24 volt, 0.1 amp) to be...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

If you don't know how to mirror a model in your slicer, please research this first or you risk wasting a bunch of filament.Follow the same pattern if you print on a larger printer. Make sure to still print the "sliding supports"</p><p>You should not...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protectionSuperior...

See overview here for model comparisons: https://makezine.com/2014/11/22/review-airwolf-hd-hdx-and-hd2x-3d-printer/ The Airwolf APEX Software has pre compiled firmware included for all the HD series but the m500 command is disabled. The public...

The very bearing is a round 4mm rod with a thread just at one end, available as model landing gear axle. "009a_servo_gear" Juan's design provides very small holes for the screws, fitting the gear to the pan servo disc. Since drilling...

Presupported files are included for each model in both STL format and LYS (Lychee Slicer) format so you can rescale them if required.  Presupports have been created and tested by Ty Mansfield, at The Tabletop Engineers.   Talarius is a melting pot...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Your One-Stop-Shop for Premium 3D-Printing models. Get started with the Ultimate STL platform! Click here to join STLFLIX It’s a Mushroom Lamp This STL file is recommended for FDM Printers!3D Printing Time: Approximately Height :  21 cm The perfect...

idk what slicer or print settings were used on the original print, but I had to redo the entire geometry of that area to get it to print right without disturbing the bevel of the rest of that model. Unfortunately, given I don't have the original...

Use "leveling_test.stl" model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! Update 1: My Start and End G-codes in Cura working well with this firmware: ...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

For the paddles, you can use the stock G29/G27 etc paddles, or you can print the ones I have modeled. You will need 4x M3x10 screws for this. The quick release adapter I provided uses a 70mm bolt spacing. **********While this is still...