tribute 2 phone case 3d models

This is a case for the LG L33L "Sunset" and "The Tribute 2" This case was designed to be printed standing up so the radius on the back comes out nice. It can be Printed laying down on its back but move the model 1.4mm down in to the plate so the...

terminator 2 tribute

I thought it would be fun to make a Raspberry Pi case in the shape of the RetroPie logo as a tribute to all those that volunteer their time to the RetroPie project. I have not made this case yet, so if you find problems I apologize. I have also...

I thought it would be fun to make a Raspberry Pi case in the shape of the RetroPie logo as a tribute to all those that volunteer their time to the RetroPie project. I have not made this case yet, so if you find problems I apologize. I have also...

This is my second remix of this great case with further refinements a few improvements and a cool new feature **FUNCTIONING BUTTONS !!!** The buttons now safely **Shutdown** and **Restart** the Retropie Summary of the changes I have made: *...

this is my take on the jelly 2 phone case

I made this case for my Razer Phone 2, Used NinjaFlex filament and came out good. ...Thought I share with everybody....

Basic hard (PLA) phone case design for the Pixel 2. ...Other files I found block the sensor below the rear-facing camera sensor (thus the more square cutout).

A basic case designed for the [Razer Phone 2](https://www.razer.com/mobile/razer-phone-2). It is a tight fight and works best as is with semi-flexible materials. ...For PLA, it may need to be scaled up a small amount but I have not tried that out.

i beefed up the back of the phone so you coud sink it in to the buildplate and still get the inside curve but the outside is flat the width is 1.2 sink it in to the build plate to get the single layer bottom :) i also reduced the amount of distance...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_custom_dimensions = 0 custom_back_camera_y_size = 20 stencil_pattern_element_rotation = 0 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 0 stencil_shape = 4 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_right_port_corner_radius = 5 custom_left_port_length = 50 custom_phone_thickness = 10 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 use_pattern = 1 stencil_shape = 4 custom_right_port_corner_radius = 5 custom_back_camera_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=58001 Instructions Using the following options: pattern_rotation = 13 iphone_version = 1 4swidth = 6.17 pattern_overlap = 18 4sthick = .6 4cornerR = 8 4length = 115.25 5_height_tolerance = .2...

http://www.thingiverse.com/apps/customizer/run?thing_id=40703 Instructions Using the following options: case_thickness = 2.4 pattern_shape = 6 iphone_version = 1 pattern_rotation = 0 pattern_thickness = 7 pattern_radius = 11 build_plate_selector = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=813330 Instructions Using the following options: 5length = 123.8 4swidth = 6.17 4width = 58.55 6PluscornerR = 8 5cornerR = 8 iphone_version = 4 5width = 58.6 pattern_shape = 6 6Pluslength =...

... take the top/bottom besel supports out, as well as the side supports (you could also just resrict supports from those areas, just make sure the image is still visible). it makes a nice lighter area so you dont have a big hole in the back of the case

Basic Printable case for the Light Phone 2. Prints in PLA or PLA+ and clips on. ...

This is a tribute for my favorite skill in Torchlight 2. My Engineer's primary attack skill almost 70-80% of the time. Spawn 9 of em and I run into the enemy crowd with shield's up and keep dropping these till everything's down. Granted it takes a...

Oneplus Nord 2 phone case, project files are included in Zip file.Project made in FreeCad 0.19!!!

I made this case for my Razer Phone 2. I thought I share. ... I made it with Ninjaflex TPU.

Phone case for Motorola Droid Maxx 2 The presentation images show one printed in glow-in-the-dark filament with full honeycomb infill.

This is a case for the LG Ultimate 2. I have posted it with the optional screen cover. ... The cover works well if you cary the phone in your pocket with other items that could crack the screen.

http://www.thingiverse.com/apps/customizer/run?thing_id=74322 Instructions Using the following options: pane_size = large image_file = lithopane_new20161029-21486-12lmv90-0.dat text_reverse = no text_line_5 = text_line_4 = text_line_3 = text_line_2 =...

2.10.1.19 After several months of using this case and multiple unintentional drop tests, the phone is still alive, although its helped point out a few design flaws. There will be a revised case design posted below in a later update, but to start with...

Small LG Stylo 2 Case

After printing, you have to stretch the case a little and walk the phone in sideways. TPU seems to be the best material for that. Not sure about any other flexible filaments. Be sure to clean up any stringing. TPU tends to have very specific print...

Since pankajbokdia asked nicely in the post of:http://www.thingiverse.com/thing:164281 I've decided to share my base models I use to make cases for my phone, there are 4 base skin models with different thickness. For my UP Plus Pro printer I use a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_back_extra_port_y_position =...