trinus 3d models

267 3d models found related to trinus.
Trinus Extruder Handle
Trinus Extruder Handle
thingiverse

Trinus Extruder Handle ~

TRINUS filament hole cover
TRINUS filament hole cover
thingiverse

kodama TRINUS filament hole cover

Trinus filament guide
Trinus filament guide
thingiverse

Filament guide for the Kodama Trinus printer.

Trinus desktop tool station
Trinus desktop tool station
thingiverse

Tool station for Kodama Trinus essentials. ...

Trinus Rail Bearing Cover
Trinus Rail Bearing Cover
thingiverse

Simple dust cover for the ends of the Trinus rails.

Trinus Gopro center mount
Trinus Gopro center mount
thingiverse

Trinus Gopro light center mount Can be installed without removing the enclosure

Trinus bed leveller thumbscrew
Trinus bed leveller thumbscrew
thingiverse

Thumbscrew for Trinus 3d printer adjustable bed to replace the original stainless steel ones which vibrate off in use.

Trinus enclosure faceplate
Trinus enclosure faceplate
youmagine

Print two of these and mount with a DC jack connector and power switch to make the Kodama Trinus enclosure a bit easier to work with.

Trinus Dial Indicator
Trinus Dial Indicator
thingiverse

Dial indicator mount for the Trinus 3D printer to allow accurate bed levelling. ... Remove back plate from dial and use screws to affix to this plate.

Trinus SD-card guide
Trinus SD-card guide
myminifactory

I was fed up with the difficulty of replacing the SD-card in my Trinus so decided to make a guide for it.

Trinus Filament Guide
Trinus Filament Guide
thingiverse

Because it has been requested, this is a remix of my Spool Holder and Filament Guide for the Kodama Trinus Printer:http://www.thingiverse.com/thing:2001057 There is now only the Filament Guide for those who would like to use their own Spool Feeder,...

Trinus filament guide
Trinus filament guide
thingiverse

Simple filament guide for Kodama Trinus. I did not use any ball bearings or similar stuff. Only part of assembly that is not printed is the 5 mm shaft that is used to fix the roller. ...Designed in Autodesk Inventor.

[Trinus] Noctua fan adapter
[Trinus] Noctua fan adapter
thingiverse

Allows you to use the silicon dampers that come with the Noctua 40mm fan made for trinus When installing make sure the little jut it pointed up I recommend printing at at least 0.1 layer height

Trinus Extruder Arm
Trinus Extruder Arm
pinshape

no additional parts required.  Design Process: Scanned broken piece on a flatbed printer/scanner, imported scan into Fusion360, traced the scan, extruded, scaled to correct dimensions, sketched and extruded text, exported, PRINTED IN ABS, installed...

Trinus spool holder
Trinus spool holder
thingiverse

Loosely based on the Trinus Spool Holder by Sylvian42 https://www.thingiverse.com/thing:2063176 I've made my own design which I found more fitting with the Trinus printer The pillars are very strong, print fast, and don't need supports. Enjoy ...

Trinus Extruder Arm
Trinus Extruder Arm
myminifactory

no additional parts required.    Design Process: Scanned broken piece on a flatbed printer/scanner, imported scan into Fusion360, traced the scan, extruded, scaled to correct dimensions, sketched and extruded text, exported, PRINTED IN ABS, installed...

Trinus LEDBERG Clip
Trinus LEDBERG Clip
thingiverse

=) Print Settings Printer: Trinus Rafts: Doesn't Matter Supports: No Resolution: 0.2 layers/mm, 3 rounds walls Infill: no infill Notes: Did not want any infill so went for 3 walls and 3 bottom/top layers. Does print without rafts on unheated bed with...

Trinus Filament Guide
Trinus Filament Guide
thingiverse

... Print Settings Printer: Kodama Trinus Rafts: Yes Supports: No Infill: 20% How I Designed This First ever 3D model, made in Fusion 360, I will be updating this with some improvements very soon, just wanted to see what I could make on my first go.

Trinus Extruder Arm
Trinus Extruder Arm
thingiverse

PRINTED IN ABS Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 40% Notes: PRINTED IN ABS How I Designed This Design Process Scanned broken piece on a flatbed printer/scanner,...

Kodama Trinus Adapter Plate
Kodama Trinus Adapter Plate
thingiverse

-> Print the adapter plate on the exact position above the print bed screws (try & error) -> Put the your printed bed beneath your print bed -> perfectly leveled Print Settings Printer: Trinus Rafts: No Supports: No Resolution: 0.2 Infill: 100%...

Trinus Gauge Mount
Trinus Gauge Mount
thingiverse

... stress on the mount. The Result: I have got a quite wavy glas surface. The waves are about 0.058mm. I need to raise the rear right of my print bed. Print Settings Printer: Kodama Trinus Rafts: Doesn't Matter Supports: No Resolution: 0.1 Infill: 40%

Trinus virtual machine
Trinus virtual machine
thingiverse

Here is my virtual version of the Trinus 3D printer from Kodama. I added rulers to the print bed to better visualize the exact location of your prints. There are two ways to install the virtual machine. They are explained in...

Trinus LEDBERG Clip
Trinus LEDBERG Clip
myminifactory

I wanted some light in my Trinus Enclosure and had a LEDBERG laying around.(http://www.ikea.com/se/sv/catalog/products/90302687/) Did not want to tape it in in fear of it coming loose and I did not want to screw it in place. This is my first model...

Trinus Tweezer holder
Trinus Tweezer holder
thingiverse

... them, or putting my SD card down and losing it. ...Now they are just inside the enclosure door and I can find them. Print Settings Printer: Trinus Rafts: Yes Supports: Yes Infill: 40% How I Designed This My first design in Auto Desk Inventor 2017

Trinus 3d Enclosure
Trinus 3d Enclosure
thingiverse

M4x16 bolts for top and bottom laser cut panels ( 8 pcs + adapters or 24 pcs without adapters) M4 or M5 x16 bolts for attaching base panel to trinus surface (4 pcs) M4 nuts as required M3x10 bolts for magnet holder (12 pcs) M3x12 bolts for handle...

Trinus LCD Holder
Trinus LCD Holder
thingiverse

I've made my own Kodama Trinus enclosure with 20x20 mm aluminium profiles with a 20 mm radius delivered by motedis. So i needed a special LCD Screen holder. Just print the holder and glue it on the radius of the profile under an 45° angle. Then just...

Altoid Kit for Trinus
Altoid Kit for Trinus
thingiverse

... is designed to just barely fit inside an Altoids tin. You'll need to apply pressure to get it into the tin; after that, it's a permanent addition (hope you like it!). Print Settings Printer: Trinus Rafts: Doesn't Matter Supports: No Infill: 20%

Trinus Pi Camera Mount
Trinus Pi Camera Mount
thingiverse

This is a Raspberry Pi camera (v2) mount for the Kodama Trinus. It works by clipping in to the frame. It's not adjustable as I wanted to be able to have it as far from the build plate as possible. The adjustable ones are too close. The camera slots...

Trinus leveling heatbed plate
Trinus leveling heatbed plate
thingiverse

Kodama Trinus 3d printer add leveling heatbed. test version. printing size 147mmx122mm. Make with aluminum plate. Aluminum plate 2 x 200 x 300 mm x 1 Flat Screw M3 x 6 mm x 3, M 3 x 25 mm x 4 Screw M3 x 5 mm x 3 Knurled RNSFS 3 x 4 Spring 0.7 x 5 x...

Trinus PolyFlex Guide
Trinus PolyFlex Guide
thingiverse

It went sideways inside the extruder, stopped the fan, and melted the filament guide I bought from Kodama (in their "Essentials Kit") So I made one from scratch that leaves very little room for that to happen, and printed it with Polymaker's PC-Plus...