triple spinner fidget 3d models
29881 3d models found related to triple spinner fidget.thingiverse
Yet another tri spinner design inspired by some of the entries already on thingiverse. The design is on onshape so modify as you like! The caps will print without support if laid on their face. Takes the usuas 608zz skateboard bearings.
thingiverse
This little hand spinner offers you something to fidget with that's silent, so as not to annoy those around you. Design and print video: https://youtu.be/r0OJFyHZ7V8 The bearings used are standard skateboard 608 bearings (I used Spitfire...
cults3d
Hexagonal Triple Armed Triple Nut Fidget Spinner Notes: Uses ONE 608 bearing and NINE 5/16" or M8 hex nuts Might not fit in a smaller hand I like using vise grips to install hardware if a nut is loose in a PLA frame, dip nut in frame into hot water...
thingiverse
Hexagonal Triple Armed Triple Nut Fidget Spinner Notes: Uses ONE 608 bearing and NINE 5/16" or M8 hex nuts Might not fit in a smaller hand I like using vise grips to install hardware if a nut is loose in a PLA frame, dip nut in frame into hot water...
thingiverse
This is a triple-decker functioning fidget spinner. It is absurd, of course, but fun to make. The key print is the connector, which snaps together two bearings that are each a part of an individual fidget spinner. The spacer is needed between them...
thingiverse
My take on the famous fidget spinner. Works with 22mmØ bearings. ...Pre-heat the bearing before putting it it, the holes are very tight.
prusaprinters
Required part: 608ZZ bearings or any 608 bearingM8 screw nutBearing dimensions: 8 * 22 * 7mmDimensions of the spinner: I designed the bearing location to be 21.8 mm. This will hold the bearings properly, but will not break...
prusaprinters
First test models had sharp edges and were uncomfortable to use.Required part: 608ZZ bearings or any 608 bearingBearing dimensions: 8 * 22 * 7mmDimensions of the spinner: I designed the bearing location to be 21.8 mm. This will hold the bearings...
thingiverse
print 1x spinner1 and 2x pispolino, than add 3x M10 Nut (check weght first to make sure all 3 have the some mass value) add an EDC 608 bearing in the middle :) you can buy on my Etsy shop:...
cults3d
This is a beautiful triple fidget spinner I designed using Fusion 360! ...Enjoy!
thingiverse
This is a beautiful triple fidget spinner I designed using Fusion 360! ...Enjoy!
pinshape
Summary This is a beautiful triple fidget spinner I designed using Fusion 360! ...Enjoy!
pinshape
Summary This is a very cool fidget spinner I designed in Fusion 360. ...Enjoy!
thingiverse
This is a very cool fidget spinner I designed in Fusion 360. ...Enjoy!
cults3d
This is a very cool fidget spinner I designed in Fusion 360. ...Enjoy!
thingiverse
This is a much more comfortable size, especially since I intentionally do not put weights into my spinners - need the fidget more than the spin! Plus the weighted ones are more dangerous to my little ones - my husband was playing with one with large...
thingiverse
This is an edit of my double ball bearing fidget spinner here:http://www.thingiverse.com/thing:1821445 Update 2: I have just uploaded a curved rendition of the original spinner which uses only the 1/2" ball bearings, but I can upload the 5/8" if...
thingiverse
For those of you who don't have a 30mm bearing for the Double-Triple XL, you can still get the beutiful design, but with a 22mm bearing. The Double-Triple is has the same dimensions and specs as it's XL counterpart, but is has a smaller ring for the...
thingiverse
I loved the triple ball bearing spinner, but it was a little too big for my younger kids. ... So I shrank it down a bit.
thingiverse
I found that 1/2 inch nuts have about the same weight/size as a 608 bearing, so I modified the spinner to use them for counterweights. I also modified the the knurling in the scad file to have not have partial knurling on the edges. I am a bit...
thingiverse
I found that 1/2 inch nuts have about the same weight/size as a 608 bearing, so I modified the spinner to use them for counterweights. I also modified the the knurling in the scad file to have not have partial knurling on the edges. I am a bit of a...
myminifactory
Available fully assembled from our Etsy here: https://www.etsy.com/listing/476178150/3d-printed-trispinner-edc-fidget-toy VIDEO: https://www.youtube.com/watch?v=GB4WBj8TMDg Our second fidget spinner! These are a ton of fun to play with, and we...
thingiverse
Our second fidget spinner! These are a ton of fun to play with, and we definitely intend to release several more models as we iterate on this design. We made the design in OpenSCAD, so the original parametric model can be easily modified. This...
thingiverse
I went on a spinner design binge today after i found some 9/16th* nuts in the garage. This one uses 3 nuts and a single bearing and is perfect for kids or anyone w/ smaller hands. ...*nuts measure 9/16th on exterior (flat-to-flat side)
thingiverse
I had some spare and also very common rc car bearings (Traxxas 5114, 5x11x4) laying around and thought I'll make a spinner with them. Since I couldn't find a spinner on thingiverse that fitted my small bearings I made my own in Autodesk 123D Design.
thingiverse
The Double-Triple XL is a masterpiece of a spinner. It features a 30mm center bearing and holds one 15mm marble(or ball bearing) and two 10mm marbles(or ball bearings) on each end. These features give it the name it bears. Not everyone has a 30mm...
pinshape
Use standard 608 ball bearings (diam 22mm) It's lighter than my quintuple/sixtuple hex nut spinner for a pleasurable spinning experience ! I also added a "short version" with a slight different design. If the nuts are too loose you can glue them. Or...
thingiverse
Use standard 608 ball bearings (diam 22mm) It's lighter than my quintuple/sixtuple hex nut spinner for a pleasurable spinning experience ! I also added a "short version" with a slight different design. If the nuts are too loose you can glue them. Or...
thingiverse
Customized version of http://www.thingiverse.com/thing:2166709 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2166709