ts100 iron 3d models

## TS100 Iron Holder for Weller WLC100 *** ### __Usage__ This soldering iron holder is meant to attach to the Weller WLC100 soldering station by clipping over the right side at the front and then sliding back to the desired position. It is designed...

Box with lid for 15 soldering tips for TS100. Soldering tips are clicked into base. Similarly as lid. There is also place on hex key and two screws. ...

Slim case for the TS100 Soldering Iron Listing on Etsy: https://www.etsy.com/listing/875012067/ts100-soldering-iron-slim-case

Store TS100 Soldering Iron, 4 spare soldering tips, stand, and adapters. ...

Ergonomic and compact Ts100 Soldering iron station with combined tip cleaner cup. ... Prints in three parts,

Case for the TS100 soldering iron. Slot for the TS100, 2x tips and 1x allen key. ... Lid with or without text available.

My Miniware TS100 soldering Iron. I wanted to make a stand for it and decided to model it quick for fun. ...Photo of the stand included as well.

Remix of the [TS100 Soldering Iron Box for ⌀5x1.5mm magnet](https://www.thingiverse.com/thing:3035775 "TS100 Soldering Iron Box for ⌀5x1.5mm magnet") from [ort](https://www.thingiverse.com/ort) to match the different size of my solder stand. ...Mine is...

Remix of the TS100 Soldering Iron Box for ⌀5x1.5mm magnet from ort to match the different size of my solder stand. ...Mine is 40 x 47 mm.</p> Category: Tools

This is a Holder for the TS100 soldering iron. Add a M8x25mm washer to prevent the plastic from the heat. ...The washer should be 2mm thick, if not you can leave a message, i can change the size.

... 15% Infill without supports. You'll need these things: 6mm x 2mm Magnets. ...- https://amzn.to/34ZNVTG TS100 Soldering Iron - https://amzn.to/3pHbOHL If you'd like to modify this file, here's a Fusion360 Link! https://a360.co/2X4vt84 Share and Enjoy!

A case I designed for my ts100 soldering iron. It holds the ts100 with a tip installed and 2 extra tips. as well as the hex bit for swapping tips out. it is held shut with magnets which are 6x3mm. You will need 5 of them. ...4 for the box mechanism...

Yet another TS100 soldering iron stand :) This stand does not need any extra hardware and is printed in just one part without any supports. Just make sure your bridging settings are correct. It can hold the iron cable weight just fine. ...The featured...

This is a Soldering Iron Stand intended for the TS100 Soldering Iron and is made from a copper water pipe. The design is provided as an SVG file which should be printed out and the selected template cut out and wrapped around the pipe and then cut...

This is a Soldering Iron Stand intended for the TS100 Soldering Iron and is made from a copper water pipe. The design is provided as an SVG file which should be printed out and the selected template cut out and wrapped around the pipe and then cut...

PLEASE DOWNLOAD FROM PRUSAPRINTERS.ORG https://www.prusaprinters.org/prints/82755-ts100-soldering-iron-pegboard Remix of the following IKEA Skadis TS-100 soldering iron holder by alexeyzel https://www.thingiverse.com/thing:4579408 added 2 spaces for...

Simple case for TS100 soldering iron based on Ф20х2 aluminum tube (OD = 20mm, ID = 18mm) It requires 180mm long aluminum tube, and those are the two caps. Upper cap has a roll for soldering tin, and the lower cap has a small cup for grease-type...

3/22/2018 update: added STEP file 4/18/2018 update: fixed STEP file Store TS100 Soldering Iron, 3 spare soldering tips, and stand Use 5pcs D6.3x2mm magnets Printer: Anycubic i3 Mega Rafts: No Supports: No Resolution: 0.2mm Infill: 20%

Yes another TS100 Soldering iron station, well I wanted just a quick lay on type of holder/station, so I designed this with that in mind, and to stop it sliding on the work surface I just used stick-on rubber feet, there is nothing stopping the iron...

Ergonomic and compact Ts100 Soldering iron station with combined tip cleaner cup. Prints in three parts, Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 Infill: 15 Filament: Prusament PLA Pearl Mouse ...

...Designed for the TS100 Soldering Iron. Designed to fit an OD 15mm ID 9mm or 10mm x 0.5mm or 1mm thick washer (a common size found at home depot, DIY stores, hardware stores, etc). No supports needed when printed standing upright as it would be used.

I have a TS100 soldering iron. I was very pleased about this iron since it is programmable and overall lightweight. However, most standard soldering iron holders are not capable of holding this iron due to the small form factor. After looking at...

I really like my TS100 soldering iron. It came in a nice but ultimately non-durable cardboard box, so I was looking for a case in which to put the iron and accessories. **CHANGES** The best, from my point of view, was vchan3m's design but I...

Version 4 updated 2017-02-01 - added holder for allan key in top cover (visible on picture) Printed on Prusa i3 mk2, You need 2x M3x20 bolts for hinges. Clamp need to be printed twice. I`ve decide to use clamps that can be replaced without needs of...

Boîte pour TS100 avec des supports pour deux pannes, la clef allen et un t-stand. Nécessite deux vis m3x30 pour la charnière. ... Le fichier FreeCAD est fourni.

Remix of the TS100 Soldering Iron Short Case to hold two spare tips without the soldering iron body.

I bought a TS100 iron and love it however, I could not use any of my old iron holders since the TS is much smaller. I designed this simple insert that fits into a cheap eBay soldering iron stand. Printed fine without supports. ...

I bought a TS100 iron and love it however, I could not use any of my old iron holders since the TS is much smaller. I designed this simple insert that fits into the cheap Element soldering station stand. ... Printed fine without supports.

I wanted a case for my ts100 soldering iron that matched my driver set. ... You will need 5 6x3mm magnets (4 for holding it closed and 1 to hold the hex key in)

A slim case for the TS100 soldering iron without any wiggle room and a friction fitted cap. Protects the iron in my toolbox. ... [Buy the TS100 on Banggood (Affiliate...