tslim x2 case 3d models
212276 3d models found related to tslim x2 case.thingiverse
This is a case for a Tandem T:slim x2 insulin pump. I broke mine so I set out to design a new one (I didn't want to wait the 2 weeks to get one shipped.) Luckily it's only taken me 3 weeks to design and print this :-) The case is designed to be...
thingiverse
Remixed version of the Tslim case by DonBroyles: https://www.thingiverse.com/thing:3124611/files I removed part of the case to eliminate the need for this to be printed in flexible filament. The pump should just slide down from the top. I also made...
thingiverse
I liked the design of the case by DonBroyles here: https://www.thingiverse.com/thing:3124611 but I prefer to wear my case horizontally. Use his print settings for the TPU case and PETG for the case clip. ...I used a 50% infill on the clip and 3 walls.
thingiverse
Remixed to protect the front LCD. ... Works well printed with PETG.
thingiverse
just a simple case for a tslim pump that can hold a airtag. In many of the t1d support groups I'm in I've seen parents talk about their kids taking off their pump for gym class and misplacing them. ...The pump slides in the case face in so...
thingiverse
Wall Mounted Charging Station for Tandem Slim X2 insulin pump. Two versions-- Version 1 fits a pump with the T:Case or T:Holster. ...Version 2 fits a pump with no case.
thingiverse
A full-size case for the AUAV-X2 Flight Controller, a very compact Pixhawk-Clone. All pins and sockets are protected. No screws needed, top and bottom shells click together. ... The FC sits snug within the case, but you can use short pieces of 2mm...
thingiverse
A simple case for the Odroid X2. It is printed in two parts, a top and a bottom, which fit together and can be attached together permanently with screws or glue. There are screw holes to mount the Odroid that accept #4 screws. Also, a large circular...
thingiverse
Protective dual travel case for 18650. ...If you have your batteries in shrinking tube, then you should scale this file up for ~1.05
youmagine
No screws needed, top and bottom shells click together.The FC sits snug within the case, but you can use short pieces of 2mm carbon rod and stick them into the holes prepared already for that.
thingiverse
These Batteries are used in the Key Fob of my Car and I wanted to have 2 spare batteries stored in the car in case a Key Fob Battery gets empty while on holiday. It was designed with Freecad (please someone should add this great Open Source...
thingiverse
and using TPU just new to Ender 3 v2 13-14 hours out of 16 for my setting case and top printed same time no need for supports, will fix if i have issues with the case but the shashibo should stick out 3mm like i designed it to to hold the top in...
prusaprinters
These Batteries are used in the Key Fob of my Car and I wanted to have 2 spare batteries stored in the car in case a Key Fob Battery gets empty while on holiday. It was designed with Freecad (please someone should add this great Open Source Program...
thingiverse
So made up this little case for it, all the openings are accessible, the Micro SD card slot, the reset hole, the Micro USB for charging and file transfer (made to fit the stock plug that comes on the cable with it) and also a hole for the headphone...
thingiverse
This one might not yet fit well (to be tested, please post results in the comments) thanks to aurelioponz for helping me with this one :) Update 2013-04-07 ~12:00: new v0.1 design (might still not fit, just some stuff added) Update 2013-04-07...
thingiverse
This is a case for the Oppo Find X2 Lite. Print it with TPU filament. ... Print settings: - 0.3 mm - 100% infill - supports
thingiverse
Here i made a case for the ESP-12F_Relay_X2 module. There are 2 versions of the lid, one with a additional hole for a extra pair of contacts. ...I use it for a extra switch input.
thingiverse
This case with a lid will hold two each of an Altus Metrum Mini or Altus Metrum Timer
thingiverse
Case for Insta360 one x2 with premium lens. ... The hinges should be melted on one side.
thingiverse
Simple Case for ESP12F Relay X2 development board. I was looking for a small MQTT smart device that can be powered with 24VDC and is able to switch two potential-free outputs. Unfortunately, there is nothing like this available on the market, so I...
thingiverse
3D case for the Odroid-X2 board. = Including: 1x Base_box.STL & Base_box.SLDPRT 1x Base_Top.STL & Base_Top.SLDPRT 1x Odroid-X2.SLDPRT 1xOdroid-x2-inBox.SLDASM Instructions: Please Use the .STL files to print for your 3D printer. Please print one by...
thingiverse
TIE Phantom case based on the excellent cases by Damage for the Stanley Sortimo and other cases. ...Uses a small space Print Settings Printer Brand: RepRap ...
thingiverse
Case para baterías Lipo, entran 2 Baterias Lipo 3S de 500mah usado para armar un skate electrico.
thingiverse
if the port doesn't line up perfectly when you plug it in, it can easily be adjusted by using a heat gun or hairdryer to soften the case up to make it aline perfectly, the adjustment is minimal so won't change the form of the case that much. the case...
thingiverse
Case for a 2-channel relay controlled by esp01, version without mounting holes. The version, the case for which I just didn't find here. Place the relay board between parts and connect them carefully but with slight force. You will also need...
thingiverse
I just got my new Retroid Pocket 2+, so I came to Thingiverse to see if there was a printable case I could use for it. I found one that came close, Gadjet's 'Retroid Pocket 2 Case Slim'. This seems to be the best intersection of protection and...