tube 8 cams 3d models
411992 3d models found related to tube 8 cams.thingiverse
Zum Justieren eines Newton mittels ZwoAsi guiding cam und SharpCap. Der Tubus erlaubt es, die Kamera sicher im OAZ zu klemmen. Wen das interessiert kann sich dazu das Video von Daniel Nimmervoll zu dem Thema anschauen: Newton Teleskop mit einer...
thingiverse
... I wanted to build something similar. Unfortunately I could not find the corners they are using so I went with 5/8" plastic tube (used for electricity wires) and designed a few angles in order to couple them together. ...
thingiverse
... of http://www.thingiverse.com/thing:279111 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=279111 Instructions Using the following options: inner_height = 16 outer_height = 20 wall_thickness = 0.825 cap_diameter = 8
thingiverse
A wrench that is sized specifically for opening 8-tube PCR strips quickly (both domed- and flat-top tubes). ... If you want to open rows of larger tubes, look at [KaiLun's multi-decapper](http://www.thingiverse.com/thing:196526/).
thingiverse
A small yet nice model of a one sided 1/8 inch tubing connector one with both is in profile Please donate!!
thingiverse
This 8-tube design was modified by Donald Bell from a design shared on Thingiverse by dwmartin805 that accommodates 15 tubes. https://www.thingiverse.com/thing:500062 Like the original the holes are designed to fit 3/16" ID polyethylene barbed tube...
thingiverse
Tube rack with 8 x 12 positions (similar to a 96 PCR plate pattern). It is composed of 4 parts that can be printed on a small volume (20 x 20 x 20 mm) and assembled post printing. I am using a 3D pen to seal the bottom parts together, and the top...
prusaprinters
Clamp for 7/8" Tube. uses ¼" hardware. includes recessed counter bore for socket head cap screw and recessed hex bore for captive nuts. use the bracket with screw inside like a stud our mount your object into the captive nut. ...Thise was used to mount...
prusaprinters
My R-8 collets were not sent to me in their typically tubes, but in a cheap flat pack. This made it difficult to get them out of the flat pack and pick the correct size the first time. These tubes are simple in design and easy to print.
thingiverse
This model is built to hold a 3/8th OD silicone tube to the wall by gluing 14mm (or under) magnet into the holes of each model. This lets me use my waterline and then secure it quickly to keep it from getting dirty. The holder is 16mm wide, 16mm...
thingiverse
Customized version of https://www.thingiverse.com/thing:4681765 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4681765
thingiverse
Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573
thingiverse
Due to interrupted supply chains a lab in my home town ran out of the original tube strip openers from wizbiosolutions and asked for a replacement. Here it is. This design is currently tested by the lab, so **use at your own risk**. They still...
thingiverse
There also is one hole on the top of the part which is slightly smaller than 1/10" (diameter) and it is intended to be used to apply pressure to the 3/8" (diameter) dowel and prevent it from slipping out. created by Alex Hilger (11/30/2015). ...Print...
thingiverse
... Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1341945 Instructions Using the following options: bottom_radius = 3 bottom_thickness = 3 lower_wall_thickness = 3 upper_wall_thickness = 3 inner_diameter = 21.8 total_height = 25
thingiverse
these are the cams for the servo setup up front. ...the split cam needs to be mirrored and you need two control cams for the front
youmagine
"CAMS" stands for "Camera Accessory Mounting System" and this is the first piece, which is meant to mount an LCD Display to a RED Camera, but you can use it with anything that uses standard 1/4" mounting hardware.There's a bit more info in this blog...
prusaprinters
Using the claw or a pair of beaks to set home X/Y with eggs to maintain the angle and then use cams to hold into position works really well for repeated jobs of the same type. Or just use them as you need! </p><p>The...
thingiverse
"CAMS" stands for "Camera Accessory Mounting System" and this is the first piece, which is meant to mount an LCD Display to a RED Camera, but you can use it with anything that uses standard 1/4" mounting hardware. There's a bit more info in this...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=813330 Instructions Using the following options: pattern_overlap = 18 pattern_shape = 6 6Plusswidth = 6.1 6_height_tolerance = .2 6Plus_height_tolerance = .2 iphone_version = 2 6Plusheight =...
thingiverse
This has been modified from the original version, including cleaning up some of the angles, adding material in front of the tube holes, and adding a slight cutaway for grasping the holder while pipetting.