tube pro 3d models
138466 3d models found related to tube pro.thingiverse
I've included two versions, one for the Palette 3 Pro and the non-pro version Uses 4mm OD PTFE tubes I also used a 4mm drill bit to clean out the holes Print in place no support Material used: PETG Nozzle: 0.4mm Layer height of 0.32 Width 0.5 Wall...
thingiverse
How to put the cable into the winding tube.
thingiverse
There are two versions of the buffer tube, a Mil-Spec version usable with most airsoft buffer tube stocks and a tube made to fit a Nexus Pro adjustable stock, as it is different from Mil-Spec. ...The Nexus Pro buffer tube is also shorter due to design...
thingiverse
How to put the cable into the winding tube
thingiverse
Holder for the Ultra Pro playmat tube (https://www.ultrapro.com/product_info.php?products_id=2298) to keep it from rolling off the table while playing.
thingiverse
Extended CaptInsano's tube extender 10mm longer, so Helmi74's tray (https://www.thingiverse.com/thing:2319146) would work for the Gaggia Classic Pro. ... CaptInsano's came just a tad short for the Pro, maybe tube lengths are different between that and...
prusaprinters
Holder for the Ultra Pro playmat tube (https://www.ultrapro.com/product_info.php?products_id=2298) to keep it from rolling off the table while playing. Category: Hobby
pinshape
I made these to hold the waterproof case for my Yi Action camera. ...It uses the standard Go Pro Mount style. It uses American Sizes, because that is what the shop has the most of. 10-24 socket head and nut trap to clamp on 3/4 and 1 inch tubes.
thingiverse
... nut you see in the pictures. The PTFE tube slides right through the 4mm fitting and down into the little metal guide down below, where the short piece of tubing used to go. ...Now it is one solid piece of tube from the extruder to the hot end.
thingiverse
This is a customizable holder for Flashforge Creator Pro filament guide tubes. It holds the end of the tubes away from the printer case to avoid entanglement and in an angle that fits the Makerbot acrylic dome...
cults3d
This is a customizable holder for Flashforge Creator Pro filament guide tubes. It holds the end of the tubes away from the printer case to avoid entanglement and in an angle that fits the Makerbot acrylic dome...
prusaprinters
I printed a new one today using Hatchbox yellow ABS with support material and got very good results (slicing with Simplify3D). This is a customizable holder for Flashforge Creator Pro filament guide tubes. It holds the end of the tubes away from the...
thingiverse
Needed a more stable tube holder for my cr10s pro. ...uses the grommet that came with the original holder.
thingiverse
Two brackets to fit the Sena Prism Tube action camera to enable fitting to go pro type mounts the camera just clips into the mount but I have included a slot to allow fitment of a cable tie to hold the camera in place if required.
thingiverse
With the flashforge creator pro, the tubes don't plug well on the top plate, and they sometime remove themself. I decided to remix DrLex's design to resolve the problem. Easy to print, maybe better with high temperature materials but i don't think...
cults3d
Looking for a simple, strong and effective FlashForge Pro Creator filament guide holder? You are in luck. This is a non nonsense replacement that is strong, allow you to position it any way you want and doesn't stand in the way when you work on your...
cults3d
Looking for a simple, strong and effective FlashForge Pro Creator filament guide holder? You are in luck. This is a non nonsense replacement that is strong, allow you to position it any way you want and doesn't stand in the way when you work on your...
prusaprinters
Set your slicer of choice to have a strong part (top/bottom/shell layers, temperature, infill, etc). Before installing this part, make sure your filament tube fits it nicely. If it's too loose or to tight, no worries, just heat the part gently with a...
thingiverse
Looking for a simple, strong and effective FlashForge Pro Creator filament guide holder? You are in luck. This is a non nonsense replacement that is strong, allow you to position it any way you want and doesn't stand in the way when you work on your...
thingiverse
Designed this part to connect my Palette Pro to the Ender 5 Plus. Pretty straight forward and easy to install. Quick print and doesn't require any supports. It attaches to the filament sensor by removing the four screws and putting this part on the...
thingiverse
Hello there this is a simple PTFE Tube Guide for the Ender 3 (Pro). It helps to guide the PTFE Tube (Filament) straight into the hotend and prevents twisting and eventually blockage of the hotend/PTFE Tube. It's designed for a Micro Swiss Hotend and...
thingiverse
Fliment tube always fall out unless there is filament in them. ...Print Settings Printer: Flashforge Creator Pro Rafts: No Supports: No Resolution: 0.2 mm Infill: 20% Post-Printing Sand it a bit if they're too tight.
thingiverse
I just wanted a simple Bowden tube holder for my Ender 3 S1 Pro, so I could have a second filament on the ready. Using an m3 x 16 screw to attach to the existing spool holder. ...
thingiverse
The late 2016 version of the Flashforge Creator Pro has modified the filament tube bracket into a really awkward to use V grip thing. This bracket clips into these V grips and greatly improves the filament handling. Simply press the bracket into...
thingiverse
This is a filament input tube holding clip for the Palette 3 Pro. It allows filament to be fed in by 4MM OD tubes (similar to those used for standard Bowden tubes) I use this to prevent the filament from accidentally slipping out of the Palette as I...
thingiverse
I had this Philips LED Tube lying around and I wanted to use it as a light for my Creality Ender 3 Pro. So I designed this holder for it in Fusion 360. I also uploaded the Fusion f3d file so you can make adjustments if needed. ... Enjoy :)
thingiverse
This is an extender for the Dart Zone Nexus Pro buffer tube. As simple as that. There is only one hole to put the stock on, but I'll design a longer alternative if there is demand. Proudly designed with Blender. *If it loads in your slicer too...
prusaprinters
It helps to guide the PTFE Tube (Filament) straight into the hotend and prevents twisting and eventually blockage of the hotend/PTFE Tube. It's designed for a Micro Swiss Hotend and installed on a Ender 3 Pro but it should also work with the Ender 3...
thingiverse
I ran into a problem with my Ender 5 Pro on prints that used the full area of the bed: the Bowden tube and nozzle power cable would get caught on the y-axis motor head, impeding motion of the y-axis and making a heck of a racket. This retaining clip...
thingiverse
These little inserts fit into the guide tube slots on the back of the Flash Forge Creator Pro to allow the guide tubes to protrude from the back of the printer allowing non indented hub spools to have the filament fed more in line with the inner roll...