tunnel plug 3d models
56574 3d models found related to tunnel plug.cults3d
Anal Tunnel Plug Diameter: 4cm Diameter of the opening: 2.5cm Height: 10cm Width of the base: 6cm
myminifactory
10mm tunnel plug single flared. Needs an O-Rubber on the backside to stay. Enjoy! ... file created in OnShape
thingiverse
Keep in mind health risk when using non-foodgrade materials. You might want to scale down plop, especially when coating after print. ... Sorry for not designing the file around the z axis, rotate 90° for printing of course.
thingiverse
This is a replacement twist-on cover for the tunnel holes in a CritterTrail hamster/gerbil cage. Instructions I printed this in PLA at .2mm layer height. ...The OpenSCAD source is included as well, so...
cults3d
Tunnel Butt Plug. Simple butt/anal dilatator with an hole inside. ... Made with Blender 2.8 Measurements: mm: 59.7 x 59.7 x 94.9 Check my other creations:https://cults3d.com/en/users/FakeAlex/creations
cults3d
My version of a tunnel butt plug. ... Made with Blender 2.8 Measurements: Total (mm): 78.4 x 49.1 x 78.0 Widest insertable (mm): 49.1 x 49.1 Inner hole (mm): 27 x 27 Base (mm): 78.4 x 49.1 Check my other...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/8VvIymplZ3S
thingiverse
... fall out, as do the adjustable width. P.S.: The Thingiverse Customizer does not yet support booleans it seems, so for now only plugs can be made here (you can however with the smaller tunnels crank the thickness up and create a tunnel that way).
thingiverse
It's hard finding low priced plugs past 50mm, so I made these. If there's any demand for bigger sizes, I can put them on here too. ...I have models made up to 75mm.
thingiverse
I was tired of the commercial tunnel plugs which are big, long and straight, they lean against the wall of the rectum and block the passage. I did a brief anatomy analysis and drew this model. I believe that the angle of passage and the length of...
thingiverse
Customized version of https://www.thingiverse.com/thing:4719515 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4719515
thingiverse
Customized version of https://www.thingiverse.com/thing:4719515 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4719515
thingiverse
Customized version of https://www.thingiverse.com/thing:4719515 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4719515
thingiverse
Customized version of https://www.thingiverse.com/thing:4719515 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4719515
thingiverse
Customized version of https://www.thingiverse.com/thing:4719515 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4719515
thingiverse
Customized version of https://www.thingiverse.com/thing:4719515 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4719515
cults3d
8mm ear tunnels and plugs, feel free to make them bigger or smaller as you need
thingiverse
8mm ear tunnels and plugs, feel free to make them bigger or smaller as you need
thingiverse
Plug Tunnel and Glasses holder for Bahtroom Plug Tunnel und Brillen halter fürś Badezimmer
thingiverse
My first Solidworks desing, usually using AutoCAD. ...I was using Cura to slice model and resized it to 9.5 x 9.5 x 6 mm
thingiverse
just as the name describes. meant to be printed as two parts then glued together, i print in abs and use abs/acetone mix to glue and smooth for comfort. no supports needed. add things to the centers, make your own custom jewelry. ...wearable diameter is...
thingiverse
The earring is 10 millimeters in diameter but you can resize it as required. ... Printed using a 0.35mm nozzle and yellow "glow in the dark" ABS.
prusaprinters
... and the 10 mm tunnel is at least 1mm thick (in the middle a bit more). I have not tried to print the tunnels with a fdm printer yet (only with my elegoo mars) Print instructionsUnassociated tags: ear piercing, ear plug, ear tunnel Category: Earrings
thingiverse
... thing to create a flesh tunnel and made a hole with a bulge in it. ...The wall of the 20 mm and the 10 mm tunnel is at least 1mm thick (in the middle a bit more). I have not tried to print the tunnels with a fdm printer yet (only with my elegoo mars)