turnigy 9x 3d models
3184 3d models found related to turnigy 9x.thingiverse
Remixed version of very usefull upgrade for Turnigy 9X. ... Dont forget to like my work ;-).
thingiverse
Protect cover for Turnigy 9x Sticks Print Settings Printer: Prusa i3 Rework Rafts: No Supports: Yes
thingiverse
Holder for remot control Turnigy 9X, for protect stick from damage during transport.
thingiverse
This is a cradle for recording your flights from a tablet or phone by attaching it to your turnigy 9x radio with a Velcro strap and a rubber band over the recording device. I use this to record third person while flying FPV. ... ...
thingiverse
A modified version of the Monitor Support by Straub for the Turnigy 9X. I have an Eachine LCD5802D Monitor but it should also work with other ones. You'll need a M5 x 50 bolt and an M5 nut and you can get a grip for the bolt from the original support...
prusaprinters
A modified version of the Monitor Support by Straub for the Turnigy 9X. I have an Eachine LCD5802D Monitor but it should also work with other ones. You'll need a M5 x 50 bolt and an M5 nut and you can get a grip for the bolt from the original support...
thingiverse
This is designed for Turnigy 9x, but it can be used also on other transmitters where is round antenna. Bottom hole is ø9,5mm and top hole is ø8mm. Cover the front side of booster with aluminum or copper foil tape. I used 0.5mm thick polished aluminum...
thingiverse
I do have to put a plug in for the ER9X replacement firmware for the Turnigy 9x. It makes more sense for me then the stock turnigy V2 firmware. Instructions Nothing is too critical. Print the...
thingiverse
This is simple stick protector for Turnigy 9x transmitter.
thingiverse
Sandwich mounting aparatus for common action cameras to turnigy 9X radio.
thingiverse
This is the standard version for the stock Turnigy 9X sticks. ...Check out my WIDE version, which fits 20mm thumb sticks (https://www.thingiverse.com/thing:2913753). Designed for the Turnigy 9X / FlySky 9X / TH9X, but they may fit other radios.
thingiverse
These fit thumb sticks (20mm wide). ...See my other Things for the standard stick version (https://www.thingiverse.com/thing:2437633). Fits the Turnigy 9X, FlySky 9X and other rebrands.
thingiverse
This is the self centering lever for the Turnigy 9X. You will need a spring. The only problem with the model is that the hole for where the rod goes through is a little messed up, but it can easily be drilled out and work perfectly! I made one for...
thingiverse
Remixed the bracket to fit a Turnigy 9X by extending it longer to fit the metal bracket on the controller. Used Meshmixer to cut, copy and extend the bracked Instructions Use standard hex M3 nut or...
thingiverse
Allows you to remove the stock Turnigy 9x antenna and use an SMA antenna instead on the top. Instructions I made it a hair larger to account for a bit of shrinkage of the ABS, so you may want to...
thingiverse
Allows use of a 3 cell 2200mah LiPo battery in a Turnigy 9x Radio Transmitter. Instructions Print without support, I used 2 perimeters in Slic3r (1.0.0RC2) (.35mm nozzle). A brim (as it is called in...
cults3d
When you want to change the Tx module of the Turginy 9X radio, you just discover that tha antenna is hard wired into the radio which makes it impossible to remove the Tx. Just open the Tx, unsolder the antenna wire (take a picture before as you'll...
thingiverse
When you want to change the Tx module of the Turginy 9X radio, you just discover that tha antenna is hard wired into the radio which makes it impossible to remove the Tx. Just open the Tx, unsolder the antenna wire (take a picture before as you'll...
thingiverse
Battery cover for Turnigy 9X transmitter to hold a 2S 7.4V 5000mah Li-ion Battery or similar. For example the one for TX16S. ... Printed with supports.
thingiverse
I've designed this and use it for holding this screen: http://www.banggood.com/FPV-4_3-Inch-TFT-LCD-Monitor-Screen-For-RC-Models-p-940817.html on my Turnigy 9X remote.
thingiverse
This is a return lever for Turnigy 9X. It permits for the joystick, thanks to a spring, to go back in neutral position by itself. Usefull if you want to have the neutral position on your throttle joystick (which wasn't with my radio out of the box).
cults3d
This is a receiver holder and protector for the Turnigy 9X Receiver, Its holds the receiver very good and fits perfectly by pression, no need screws, use a belt for mount it. ... Leave positive comments, like and share it, that would help a lot!
thingiverse
This is an antenna cap for the Turnigy 9x transmitter. It protects the transmitter's board from dust, if you remove the embedded antenna (recommended) when you make the module mod. There is a hole to fix the cap with the screw of the original...
thingiverse
This is a receiver holder and protector for the Turnigy 9X Receiver, its holds the receiver very good and fits perfectly by pression, no need screws, use a belt for mount it. Leave positive comments, like and share it, that would help a lot! ... - ...