turnigy camera 3d models
110128 3d models found related to turnigy camera.thingiverse
Then your choice of strap through the bottom mouth to hold the camera. ...Print Settings Printer: Wombot Rafts: No ...
thingiverse
Lightweight FPV case for the Turnigy Action Camera. Much less weight than the waterproof case. No supports needed to print. Uses two M2.4 or M2.5 bolts for the back and two for the lens cover (available online or Home Depot). Print the layer lens...
thingiverse
This is for the Lumenear 250 frame. ...It will hold a SJCam or the Turnigy 2k camera. ...This is revision 1 and has not been printed yet for testing.
thingiverse
This is a little plate the sits in the GoPro seat on the top of your TBS Vendetta and supports a Turnigy action camera or similar (iSaw AIR camera for example) in that space. Lightweight it weighs less than 4g when printed with 505 infill and...
thingiverse
Useful to pop over the lens when you are carrying the camera without one of the larger enclosures. ...Print Settings Printer: Geeetech Rostock G2s Pro ...
thingiverse
This is a simple mount to allow you to use a Turnigy action camera on models that expect to have GoPro style mounts. We're using it here on a Nova Pro from HobbyKing. Print one of the bases and two of the arms, use a paperclip as the hinge. This...
thingiverse
Sandwich mounting aparatus for common action cameras to turnigy 9X radio.
thingiverse
A quick, lightweight guard I threw together for the Turnigy 2K HD camera gopro clone. Still a work in progress, if you've got any modification ideas, let me know. ...Thanks for looking!
thingiverse
Camera holder for the Turnigy 2K HD Camera from Hobby King. The camera just slides in from the top and all of the controls and scree are accessible. The camera fits snug enough that it won't fall out if you hold it upside down but takes just a small...
thingiverse
Turnigy Hd Action Camera FPV Cover. Fits in snug, you can access the sd card on the side as well as the menu buttons. I made a spot so you can pull the camera out of the case. The Lens Protector can fit after camera is inside case. Printed in PLA.
thingiverse
... Instructions Print lying on it's side. I print with a brim to ensure good adhesion. It needs support material touching everywhere to create the internal slot for the camera and 20% infill does the job nicely.
thingiverse
An OpenSCAD version of an rPi camera mount for the Turnigy 1/16 Buggy with brushless motor. It's being used with the donkeycar.com autonomous car framework and has Customizer capabilities to adjust the mounting pin locations for different RC vehicle...
thingiverse
Camera mount for Turnigy 1/18 truck. ...One board for fitting under cover and small holder for camera with flexible joint.
thingiverse
Hood for action camera Onepaa X2000 / Turnigy Eclipse.
thingiverse
This is the camera mount for Turnigy Nitro Rumble Buggy. ...Compatible with GoPro/SJCAM waterproof case, one M5 nut is required to assembly.
thingiverse
A camera mount for a 9g Turnigy 180 pan servo. This mount allows you to easily connect an FPV camera to a servo fro a super easy pan gimbal for your model. ... I printed using PETG, depending on your printer you may need to drill the hole a bit more...
thingiverse
To install FPV camera is good idea to place it outside car body (I've tried to install it inside car but picture was so blurry and noisy). ...Just unscrew two screw on car front and place holder below.
thingiverse
You'll need everything from this http://www.thingiverse.com/thing:900859 Except the clip to use the camera mount,oh and 2 bolts and nuts, and probably a longer ribbon cable for the cam. Just hangs off the front without any screws/ adhesive,...
thingiverse
Attaches to the perspex under the print bed. I've not put holes in the model because, quite frankly, I'm new to this and don't know how. It's easy enough to drill a pilot hole! Remix of http://www.thingiverse.com/thing:279281 and you'll need the...
thingiverse
Anti vibration camera mount for Turnigy Nitro Rumble Buggy. Compatible with GoPro/SJCAM waterproof case, one M5 nut is required to assembly. ...Print Settings Printer Brand: RepRap ...
thingiverse
Remix of this: http://www.thingiverse.com/thing:241409 Which in turn is a Remix of: http://www.thingiverse.com/thing:192364 Widened the clip to 4mm so it fits the Fabrikator's perspex front, added an 80mm arm and made a version of the...
thingiverse
This is a FPV fixing Thing, You just take "Turnigy FPV200 Set w/LT200 5.8GHz 200mW FPV A/V Micro Transmitter and V700 Mini Camera" from Hobbyking and print the holder, so you are able to put everything inside and it's pretty well fixed. So you can...
thingiverse
This is a remix of the bottom half of http://www.thingiverse.com/thing:30572 It adds a mount to clip onto the front of the Fabrikator and a mount for the camera arm (you lose access to HDMI port). You'll need to source the top of your choice from...
thingiverse
https://youtu.be/aln_xYy-Z3M RC Car bodyhttp://www.thingiverse.com/thing:1043067 Turnigy 1/16 Brushless 4WD Racing Buggy w/25A Power System and 2.4Ghz Radio (RTR)http://www.hobbyking.com/hobbyking/store/uh_viewitem.asp?idproduct=56235&aff=166047...