turnigy lipo 3d models

nano-tech Turnigy LiPo 1600 mAh battery with JST connector. MPX included in assembly was the ones that I find on this site (credits to the owners). Connectors are not attached to be easy to remove them as you need. ...Feel free to use it for...

This is a case for a Turnigy Nano-tech 1500mha lipo battery. Since I'm still learning, sometimes I have really bad crashes... I've destroyed one Nano-tech and cut at least two balancer plugs. Since some of my batteries are scratched and have some...

wall mount for the turnidgy dual charger

Customized version of http://www.thingiverse.com/thing:873062 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=873062 Instructions Using the following options:...

A holder/mount for the Turnigy High Capacity 6600mAh 6S 12C Lipo Pack. This can be used to just hold the pack on a wall, or to mount it to a device that you're using it on - I use it like this for my electric conversion mower. Its not a tight fit...

Customized version of http://www.thingiverse.com/thing:348618 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=348618 Instructions Using the following options: ...

Remake of pintokitkat's battery holder. ...This remix holds a Turnigy 2.2 3C battery. ...I am using it on my Hobby king Q450 quad-copter.

Customized version of http://www.thingiverse.com/thing:873062 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=873062 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:873062 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=873062 Instructions Using the following options:...

Size: Battery length = 145mm Battery height = 25mm Battery width = 53mm hole distance length = 110mm hole distance width = 70mm fits for this Battery: https://hobbyking.com/de_de/turnigy-5000mah-3s-20c-lipo-pack-xt-90.html

This is a Lipo Guard for the Turnigy Graphene Lipos. ...Size : 102x35x9.8mm +-1mm g perfectly fits to the lipo i use 7 grams by 50% infill 0.2 layer 2 Perimeter

This is a Lipo Guard for the Turnigy Graphene Lipos. ... Size : 102x35x9.8mm +-1mm *g* perfectly fits to the lipo i use 7 grams by 50% infill 0.2 layer 2 Perimeter

2S1P 5000mAh Hardpack from Turnigy.

I didn't want my soft wrapped NanoTech LiPo bouncing about inside my OpenRC F1 car and i wanted it to be a bit safer for transport so i designed this fits inside the OpenRC F1 Electronics Holder designed by Noneus...

Turnigy 2200mAh 3S 20C Lipo Pack.

Case to store 5x Turnigy Nanotech 2S 300mah 45-90c lipos.

Battery tray to hold down a Turnigy 3s 2200 lipo I am sure that other makes of 2200 3s batterys will fit and I purposefully made the design a bit slack to allow for puffed cells Can always add thin foam pads I have printed off and built parts to make...

this is just a simple case to protect the 6s multistar 16 ah lipo battery from stress (inside the frame or bag etc) while riding your ebike. it is best to put additional "thin" foams around the battery to be more efficient. remember it does not...

Customized version of http://www.thingiverse.com/thing:348618 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=348618 Instructions Using the following options: hole =...

hereby presented for the thundertiger MT-4G3: Turnigy 5000mAh 4S1P 14.8v 20C Hardcase pack. especially for the Turnigy 5000mAh 14.8v 4S1P 20C Hard Case Pack. and of course lipo's with exactly the same measurements. Gone with that clearance between...

Turnigy nano-tech 2s battery

Customized version of https://www.thingiverse.com/thing:348618 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=348618

The BeeRotor X200 has two LiPo straps instead of 1, but unfortunately most LiPo's are too short and the straps only just catch the end of the battery. I have added two slightly indented sections that allow the straps to grip well. Given the battery...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/axH5e1sprbF

......The sleeve may be a loose fit but knowing lipos, there is room for slight swelling. For impact situations i recommend using cut out of foam to line the inside for further protections against impact and vibrations. There is no "lid" or Cap for this.

Lipo Turnigy Nano Tech 4s 1,8A Support for Martian II 220

I use these batteries to replace my old drill NiCads : https://hobbyking.com/en_us/turnigy-nano-tech-1300mah-4s-45-90c-lipo-pack.html ---------------------------------------------------------- Make sure you also use somthing like this to cut off the...

I use these batteries to replace my old drill NiCads : https://hobbyking.com/en_us/turnigy-nano-tech-1300mah-4s-45-90c-lipo-pack.html Make sure you also use somthing like this to cut off the battery before it goes under voltage :...

Solidworks 2015

Customized version of http://www.thingiverse.com/thing:873062 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=873062